công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
STK15C88-W25 bảng dữ liệu(PDF) 8 Page - List of Unclassifed Manufacturers |
|
STK15C88-W25 bảng dữ liệu(HTML) 8 Page - List of Unclassifed Manufacturers |
8 / 9 page STK15C88 August 1998 5-42 Internally, RECALL is a two step procedure. First, the SRAM data is cleared and second, the nonvola- tile information is transferred into the SRAM cells. After the t RECALL cycle time the SRAM will once again be ready for READ and WRITE operations. The RECALL operation in no way alters the data in the EEPROM cells. The nonvolatile data can be recalled an unlimited number of times. AutoStoreTM OPERATION The STK15C88 uses the intrinsic system capaci- tance to perform an automatic store on power down. As long as the system power supply takes at least t STORE to decay from VSWITCH down to 3.6V the STK15C88 will safely and automatically store the SRAM data in EEPROM on power-down. In order to prevent unneeded STORE operations, automatic STORE will be ignored unless at least one WRITE operation has taken place since the most recent STORE or RECALL cycle. Software initi- ated STORE cycles are performed regardless of whether a WRITE operation has taken place. POWER UP RECALL During power up, or after any low power condition (V CC < V RESET) an internal recall request will be latched. When V CC once again exceeds the sense voltage of V SWITCH, a RECALL cycle will automatically be initiated and will take t RESTORE to complete. HARDWARE PROTECT The STK15C88 offers hardware protection against inadvertent STORE operation during low voltage conditions. When V CC < VSWITCH all Software STORE operations will be inhibited. LOW AVERAGE ACTIVE POWER The STK15C88 draws significantly less current when it is cycled at times longer than 30ns. Figure 2, below, shows the relationship between I CC and READ cycle time. Worst case current consumption is shown for both CMOS and TTL input levels (com- mercial temperature range, V CC = 5.5V, 100% duty cycle on chip enable). Figure 3 shows the same relationship for WRITE cycles. If the chip enable duty cycle is less than 100%, only standby current is drawn when the chip is disabled. The overall average current drawn by the STK15C88 depends on the following items: 1) CMOS vs. TTL input lev- els; 2) the duty cycle of chip enable; 3) the overall cycle rate for accesses; 4) the ratio of READ’s to WRITE ’s; 5) the operating temperature; 6) the VCC level and; 7) I/O loading. Fig 3: Icc (Max) Writes Fig 2: Icc (max) Reads 50 CMOS TTL 60 20 0 Cycle Time (ns) 80 TTL 100 CMOS 80 0 40 200 100 150 50 150 100 100 40 20 60 200 Cycle Time (ns) |
Số phần tương tự - STK15C88-W25 |
|
Mô tả tương tự - STK15C88-W25 |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |