công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
M-CAS-C8237 bảng dữ liệu(PDF) 4 Page - Altera Corporation |
|
M-CAS-C8237 bảng dữ liệu(HTML) 4 Page - Altera Corporation |
4 / 5 page Word Count and Address Register Command Codes Temporary Register Read Temporary Register Command: Write -> CSN = 0, IORN = 1 and IOWN = 0 A3 A2 A1 A0 IORN IOWN 1 1 0 1 0 1 Read -> CSN = 0, IORN = 0 and IOWN = 1 Register A3 A2 A1 A0 FF DB0-DB7 0 A0-A7 CH 0 Base and Current Address 0 0 0 0 1 A8-A15 0 W0-W7 CH 0 Base and Cur- rent Word Count 0 0 0 1 1 W8-W15 0 A0-A7 CH 1 Base and Current Address 0 0 1 0 1 A8-A15 0 W0-W7 CH 1 Base and Cur- rent Word Count 0 0 1 1 1 W8-W15 0 A0-A7 CH 2 Base and Current Address 0 1 0 0 1 A8-A15 0 W0-W7 CH 2 Base and Cur- rent Word Count 0 1 0 1 1 W8-W15 0 A0-A7 CH 3 Base and Current Address 0 1 1 0 1 A8-A15 0 W0-W7 CH 3 Base and Cur- rent Word Count 0 1 1 1 1 W8-W15 This register is used to hold data during memory-to-memory transfers. Following the completion of the transfers, the last word moved can be read by the microprocessor. The tempo- rary register is cleared by a Reset. Current Address Register Each channel has a 16-bit Current Address register. This reg- ister holds the value of the address used during DMA transfers. The address is automatically incremented or dec- remented after each transfer and the intermediate values of the address are stored in the Current Address register during the transfer. This register is written or read by the microproc- essor. Current Word Register Each channel has a 16-bit Current Word Count register. This register determines the number of transfers to be performed. The word count is decremented after each transfer. When the value in the register goes from zero to FFFFH, a TC will be generated. This register is loaded or read by the microproc- essor in the Program Condition. Software Commands These three commands do not depend on any specific bit pattern on the data bus. Base Address and Base Word Count Registers Each channel has a 16-bit Base Address and 16-bit Base Word Count register. These registers store the original value, which will be loaded to current registers during Auto initialize. Clear First/Last Flip-Flop Command: A3 A2 A1 A0 IORN IOWN 1 1 0 0 1 0 This command must be executed prior to writing or reading new address or word count information to the C8237. Master Clear Command: A3 A2 A1 A0 IORN IOWN 1 1 0 1 1 0 This command has the same effect as the hardware Reset. The Command, Status, Request, Temporary, and Internal First/Last Flip-Flop registers are cleared and the Mask regis- ter is set. The C8237 will be in the idle cycle. Clear Mask Register Command: A3 A2 A1 A0 IORN IOWN 1 1 1 0 1 0 This command clears the mask bits of all four channels, ena- bling them to accept DMA requests Cast, Inc. 4 |
Số phần tương tự - M-CAS-C8237 |
|
Mô tả tương tự - M-CAS-C8237 |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |