LM78S40CN datasheet(6/10 Pages) NSC

tên linh kiện	LM78S40CN

Giải thích chi tiết về linh kiện	Universal Switching Regulator Subsystem

Download	10 Pages

Scroll/Zoom	100%

nhà sản xuất	NSC [National Semiconductor (TI)]

Trang chủ	http://www.national.com

Logo

6 / 10 page

Functional Description

SWITCHING FREQUENCY CONTROL

The LM78S40 is a variable frequency, variable duty cycle

device. The initial switching frequency is set by the timing

capacitor. (Oscillator frequency is set by a single external

capacitor and may be varied over a range of 100 Hz to

100 kHz). The initial duty cycle is 6:1. This switching fre-

quency and duty cycle can be modified by two

mechanisms — the current limit circuitry (I

pk sense) and the

comparator.

The comparator modifies the OFF time. When the output

voltage is correct, the comparator output is in the HIGH

state and has no effect on the circuit operation. If the out-

put voltage is too high then the comparator output goes

LOW. In the LOW state the comparator inhibits the turn-on

of the output stage switching transistors. As long as the

comparator is LOW the system is in OFF time. As the out-

put current rises the OFF time decreases. As the output

current nears its maximum the OFF time approaches its

minimum value. The comparator can inhibit several ON

cycles, one ON cycle or any portion of an ON cycle. Once

the ON cycle has begun the comparator cannot inhibit un-

til the beginning of the next ON cycle.

The current limit modifies the ON time. The current limit is

activated when a 300 mV potential appears between lead

13 (V

CC) and lead 14 (Ipk). This potential is intended to re-

sult when designed for peak current flows through R

SC.

When the peak current is reached the current limit is

turned on. The current limit circuitry provides for a quick

end to ON time and the immediate start of OFF time.

Generally the oscillator is free running but the current limit

action tends to reset the timing cycle.

Increasing load results in more current limited ON time

and less OFF time. The switching frequency increases

with load current.

USING THE INTERNAL REFERENCE, DIODE, AND

SWITCH

The internal 1.245V reference (pin 8) must be bypassed,

with 0.1 µF directly to the ground pin (pin 11) of the

LM78S40, to assure its stability.

V

FD is the forward voltage drop across the internal power

diode. It is listed on the data sheet as 1.25V typical, 1.5V

maximum. If an external diode is used, then its own for-

ward voltage drop must be used for V

FD.

V

SAT is the voltage across the switch element (output tran-

sistors Q1 and Q2) when the switch is closed or ON. This

is listed on the data sheet as Output Saturation Voltage.

“Output saturation voltage 1” is defined as the switching

element voltage for Q2 and Q1 in the Darlington configu-

ration with collectors tied together. This applies to

Figure

1, the step down mode.

“Output saturation voltage 2” is the switching element volt-

age for Q1 only when used as a transistor switch. This ap-

plies to

Figure 2, the step up mode.

For the inverting mode,

Figure 3, the saturation voltage of

the external transistor should be used for V

SAT.

Typical Applications

Characteristic

Condition

Typical

Value

Output Voltage

I

O = 200 mA

10V

Line Regulation

20V

≤ V

I ≤ 30V

1.5 mV

Load Regulation

5.0 mA

≤ I

O

3.0 mV

I

O ≤ 300 mA

Max Output Current

V

O = 9.5V

500 mA

Output Ripple

I

O = 200 mA

50 mV

Efficiency

I

O = 200 mA

74%

Standby Current

I

O = 200 mA

2.8 mA

Note 7: For IO ≥ 200 mA use external diode to limit on-chip power

dissipation.

DS010057-3

FIGURE 1. Typical Step-Down Regulator and

Operational Performance (T

A = 25˚C)

www.national.com

6

Số phần tương tự - LM78S40CN

nhà sản xuất	tên linh kiện	bảng dữ liệu	Giải thích chi tiết về linh kiện
Texas Instruments	LM78S40CN/NOPB	343Kb / 14P	[Old version datasheet] Universal Switching Regulator Subsystem

More results

Mô tả tương tự - LM78S40CN

nhà sản xuất	tên linh kiện	bảng dữ liệu	Giải thích chi tiết về linh kiện
ON Semiconductor	UA78S40	124Kb / 8P	UNIVERSAL SWITCHING REGULATOR SUBSYSTEM 1996 REV 1
Texas Instruments	LM78S40	343Kb / 14P	[Old version datasheet] Universal Switching Regulator Subsystem
Texas Instruments	LM78S40	322Kb / 14P	[Old version datasheet] Universal Switching Regulator Subsystem
Motorola, Inc	MC13109	381Kb / 28P	Universal Cordless Telephone Subsystem IC
	MC13109A	741Kb / 28P	UNIVERSAL CORDLESS TELEPHONE SUBSYSTEM IC
	MC13110A	1Mb / 68P	UNIVERSAL CORDLESS TELEPHONE SUBSYSTEM IC
Allegro MicroSystems	STR-A6169	194Kb / 7P	Universal-Input/5 W Flyback Switching Regulator
	STR-A6153E	192Kb / 7P	Universal-Input/20 W Flyback Switching Regulator
	STR-A6251M	327Kb / 7P	Universal-Input/15 W 67 kHz Flyback Switching Regulator
	STR-W6756	194Kb / 8P	Universal-Input/140 W Off-Line Quasi-Resonant Flyback Switching Regulator

More results

LM78S40CN bảng dữ liệu(PDF) 6 Page - National Semiconductor (TI)

LM78S40CN bảng dữ liệu(HTML) 6 Page - National Semiconductor (TI)

Số phần tương tự - LM78S40CN

Mô tả tương tự - LM78S40CN

Html Pages

1 2 3 4 5 6 7 8 9 10

bảng dữ liệu tải về

Link URL