công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
1-0519151-3 bảng dữ liệu(PDF) 9 Page - Tyco Electronics |
|
1-0519151-3 bảng dữ liệu(HTML) 9 Page - Tyco Electronics |
9 / 11 page Matrize 411-18327 Rev A Die 411-18327 Rev A Seite / Page 9 of 11 7 Maintenance / Inspection 7.1 Daily Maintenance AMP recommends that operators of the tool be made aware of the following steps of daily maintenance: 1. Remove dust, moisture, and any other contaminants from the tool with a clean, soft brush, or a clean, soft, lint-free cloth. Do NOT use hard or abrasive objects that could damage the tool. 2. Make certain that the pivot pins are in place and that they are secured with retaining plate and that locking screw of the adjustment wheel is tight. 3. All pins, pivot points, and bearing surfaces should be protected with a thin coat of any good SAE No. 20 motor oil. Do not oil excessively. 4. When the tool is not in use, keep handles closed to prevent objects from becoming lodged in the crimping jaws. Store the tool in a clean, dry area. 7.2 Periodic Inspection Regular inspections of the tool should be performed by quality control personnel. A record of scheduled inspections should remain with the tool or be supplied to supervisory personnel responsible for the tool. Inspection frequency should be based upon amount of usage, working conditions, operator training and skill and established company standards. 1. Remove all lubrication and accumulated film by immersing the tool (handles partially closed) in a suitable commercial degreaser that will not affect paint or plastic material. 2. Make certain that all pivot pins are in place and secured with retaining plates. 3. Close tool handles until ratchet releases and then allow them to open freely. If they do not open quickly and fully, the spring is defective and must be replaced. 4. Inspect the tool frame for wear or damage, paying particular attention to the tool jaws and pivot points. 7 Wartung, Instandhaltung 7.1 Tägliche Wartung Zur täglichen Wartung sind folgende Schritte durch- zuführen: 1. Entfernen Sie vom Werkzeug Staub, Feuchtigkeit und andere Rückstände mit einer sauberen, wei- chen Bürste oder einem fusselfreien Tuch. Ver- wenden Sie keine harten oder abschleifenden Mittel, mit denen das Werkzeug beschädigt wer- den könnte. 2. Stellen Sie sicher, daß der Lagerbolzen einge- setzt und durch die Sicherungsscheibe gehalten wird und die Schaftschraube zur Sicherung des Einstellrades fest ist. 3. Versehen Sie alle Stifte, Drehpunkte und Lager- oberflächen mit einem dünnen Ölfilm eines guten SAE 20 Motoröls. Ölen Sie aber nicht übermäßig. 4. Wird die Handzange nicht benötigt, dann schlie- ßen Sie die Zangengriffe und lagern die Zange sauber und trocken. 7.2 Periodische Überprüfung Eine Überprüfung der Crimpzange sollte durch quali- fiziertesPersonalregelmäßig(jenachNutzung)durch- geführt und aufgezeichnet werden. 1. Entfernen Sie jegliche Schmiermittel und Rück- stände, indem Sie die Handzange (Griffe teilweise geschlossen) in ein Fett-Lösemittel eintauchen, das Farbe und Kunststoffe nicht angreift. 2. Stellen Sie sicher, daß alle Lagerbolzen einge- setzt und durch Sicherungsscheiben gehalten werden. 3. Schließen Sie die Zangengriffe bis der Ratschen- mechanismus auslöst bzw. öffnet, und lassen Sie die Zangengriffe frei öffnen. Öffnen die Griffe nicht schnell und vollständig, dann ist die Feder be- schädigt und muß ersetzt werden. 4. Überprüfen Sie die Zange auf Abnutzung und Beschädigung, insbesondere im Bereich der Crimpbacken und Drehzapfen. |
Số phần tương tự - 1-0519151-3 |
|
Mô tả tương tự - 1-0519151-3 |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |