9--305927--1 datasheet(2/6 Pages) MACOM

tên linh kiện	9--305927--1

Giải thích chi tiết về linh kiện	Reasons for reissue are provided in Section 8, REVISION SUMMARY.

Download	6 Pages

Scroll/Zoom	100%

nhà sản xuất	MACOM [Tyco Electronics]

Trang chủ	http://www.macom.com

Logo

2 / 6 page

408- 10033

STRATO- THERM Crimping Heads

Rev B

2

of 6

Tyco Electronics Corporation

TOOL

WIRE

TOOL

SIZE (AWG)

STRIP LENGTH

1--46673--0

22 16

5 16 5 94

1--46673--1D

22--16

5.16--5.94

[ 203-- 234]

1--46988--0

16--14

[.203--.234]

NOTE: DFor wires with thin--wall insulation.

Figure 2

3. HEAD INSTALLATION AND REMOVAL

3.1. Head Selection

Crimping heads are coated with a preservative to

prevent rust and corrosion. Wipe this preservative

from the head, particularly from the crimping

surfaces.

3.2. Installation

To avoid personal injury, be sure to exercise

extreme caution when handling the crimp tool.

Avoid accidentally depressing the trigger control

when installing or removing crimp heads.

DO NOT operate the battery tool without the

proper crimping head installed. After crimping

head is installed, make sure that the quick pins

are properly inserted to avoid personal injury and

damage to the tool.

1. Remove quick pins from the adapter assembly.

Refer toFigure1.

2. Insert crimping head into the adapter assembly.

3. After the crimping head is properly aligned,

insert the quick pins through the two holes in the

adapter and through the holes in the crimp head.

The quick pins will “snap” into position when they

are properly inserted.

3.3. Removal

To avoid personal injury, ALWAYS disconnect the

battery from the tool before removing crimping

head.

Remove the quick pins from the crimping head; then

remove the crimping head from the tool holder.

4. CRIMPING PROCEDURES

To avoid personal injury, ALWAYS keep fingers

clear of crimping jaws when operating the tool.

Never place anything within the crimping jaws

except Tyco Electronics terminals or splices.

4.1. Crimping Procedure

1. Strip wire to dimensions shown in Figure 2. DO

NOT nick wire strand or use wires with nicked or

missing conductor strands.

2. Push the locator up and, from the FRONT side

of the tool, insert the terminal or splice wire barrel

sleeve into the crimping jaws making sure that the

edge of the wire barrel sleeve rests against the

locator. See Figures 3 and 4.

3. Depress the trigger to advance the moving ram.

This closes the crimp jaws in order to hold the

terminal in place. DO NOT deform the wire barrel.

4. Insert wire conductor through the insulation

barrel sleeve and into the wire barrel sleeve until it

is flush with the outer edge of the wire barrel

sleeve.

The wire barrel sleeve on high--temperature

terminals and splices is color--coded orange.

Heat--resistant terminals and splices are not

color--coded. Refer to Figure 5.

Terminal Tongue

Through Slot in

Locator

Edge of Wire Barrel

Sleeve Resting

Against Locator

Insert Wire Conductor

Through Insulation

Barrel Sleeve and into

Wire Barrel Sleeve

Push Locator Up So That Terminal

Tongue Slides Through Slot in Locator

Terminal Crimp

Insulation

Barrel Sleeve

Wire Barrel

Sleeve

Back Side of Tool

Figure 3

NOTE

i

DANGER

NOTE

i

DANGER

NOTE

i

Số phần tương tự - 9--305927--1

nhà sản xuất	tên linh kiện	bảng dữ liệu	Giải thích chi tiết về linh kiện
Tyco Electronics	9--305927--1	237Kb / 9P	Reasons for reissue are provided in Section 8, REVISION SUMMARY.

More results

Mô tả tương tự - 9--305927--1

nhà sản xuất	tên linh kiện	bảng dữ liệu	Giải thích chi tiết về linh kiện
Tyco Electronics	408-10175	340Kb / 7P	Reasons for reissue are provided in Section 8, REVISION SUMMARY.
Tyco Electronics	408-10029	237Kb / 9P	Reasons for reissue are provided in Section 8, REVISION SUMMARY.
TE Connectivity Ltd	408-8848	488Kb / 6P	Reasons for reissue are provided in Section 8, REVISION SUMMARY.
Tyco Electronics	408-4090	163Kb / 3P	Reasons for reissue are provided in Section 7, REVISION SUMMARY
Tyco Electronics	408-9243	183Kb / 4P	Reasons for reissue are provided in Section 7, REVISION SUMMARY.
TE Connectivity Ltd	408-4328	106Kb / 4P	Reasons for reissue are provided in Section 7, REVISION SUMMARY.
	408-8580	262Kb / 5P	Reasons for reissue of this instruction sheet are provided in Section 8, REVISION SUMMARY.
	408-10221	262Kb / 4P	Reasons for reissue of this instruction sheet are provided in Section 8, REVISION SUMMARY.
Tyco Electronics	408-10041	275Kb / 5P	Reasons for reissue of this instruction sheet are provided in Section 8, REVISION SUMMARY.
TE Connectivity Ltd	408-4074	238Kb / 5P	Reasons for reissue of this instruction sheet are provided in Section 8, REVISION SUMMARY.

More results

9--305927--1 bảng dữ liệu(PDF) 2 Page - Tyco Electronics

9--305927--1 bảng dữ liệu(HTML) 2 Page - Tyco Electronics

Số phần tương tự - 9--305927--1

Mô tả tương tự - 9--305927--1

Html Pages

1 2 3 4 5 6

bảng dữ liệu tải về

Link URL