công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
1--21000--9 bảng dữ liệu(PDF) 4 Page - TE Connectivity Ltd |
|
1--21000--9 bảng dữ liệu(HTML) 4 Page - TE Connectivity Ltd |
4 / 7 page 408- 10051 Rev C 4 of 7 Step--Down Adapter Splices with Step--Down Adapter WIRE SIZE (AWG) STEP CRIMPING DIE DIE AND SPLICE COLOR CODE STEP--DOWN ADAPTER COLOR CODE 8to16--14 1901006--1 Red Blue 8to12--10 1901006--1 Red Yellow 6to8 1901007--1 Blue Red Figure 5 3. Insert stripped wire into the wire barrel of the end of the splice to be crimped until the wire bottoms against the wire stop within the splice. Refer toFigure2. 4. Pivot the latch arm away from the yoke to open the head. 5. Place the splice in the stationary die. Grasp the end of the splice to be crimped and point the opposite end toward the top of the head yoke at approximately a 30_ angle. Rotate the end of the splice to be crimped into the die. Position the edge of the window indent against the locator. Refer to Figure 4. 6. Holding the splice in place, pivot the yoke and latch arm toward each other until the locking flange secures the latch arm to the yoke. Always make sure the yoke and latching arm are secured by the locking flange before cycling the tool. 7. Holding the wire in place, active the tool to complete the first wire barrel crimp. 8. When crimp is complete, pivot the latch arm away from the yoke to open the head and remove the splice. If splice sticks in die after crimping, apply a rocking action to the splice to remove it from the die. Wipe light oil on dies to reduce sticking, or use spray dry lubricant. 9. To crimp the other half of splice, reposition uncrimped end of splice in the stationary die and follow the same procedure used to crimp the first half of splice. 10. Inspect the crimp according to Section 5. 4.4. Crimping PLASTI- GRIP Butt Splices Avoid personal injury. When operating the tool, exercise caution while holding butt splices or wire near the crimping area. 1. Strip wires to the dimensions listed in Figure 2. Do not nick or cut the wire strands. 2. Select the proper color--coded butt splice for the wire size. The wire size stamped on the butt splice and on the crimping die must match the wire size selected. 3. Pivot the latch arm away from the yoke to open the head. Remove the stationary die from the yoke, then remove the locator from the stationary die. Re--assemble the stationary die onto the yoke. To avoid damage to the dies, be sure that the stationary die is properly oriented with the moving die. 4. Insert the stripped wire into the wire barrel of the end of the butt splice to be crimped until the wire bottoms against the wire stop within the splice. 5. Place the butt splice in the stationary die with the wire barrel of the end of the splice to be crimped centered over the crimping chamber. See Figure 6. 6. Holding the butt splice in place, pivot the yoke and latch arm toward each other until the locking flange secures the latch arm to the yoke. Always make sure the yoke and latching arm are secured by the locking flange before cycling the tool. Figure 6 Wire Barrel in Stationary Die Centered Over Crimping Chamber Crimping Butt Splices Locator Removed from Stationary Die CAUTION NOTE DANGER CAUTION CAUTION |
Số phần tương tự - 1--21000--9 |
|
Mô tả tương tự - 1--21000--9 |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |