công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LM3915N bảng dữ liệu(PDF) 8 Page - National Semiconductor (TI) |
|
|
LM3915N bảng dữ liệu(HTML) 8 Page - National Semiconductor (TI) |
8 / 25 page Functional Description The simplified LM3915 block diagram is included to give the general idea of the circuit’s operation. A high input imped- ance buffer operates with signals from ground to 12V, and is protected against reverse and overvoltage signals. The sig- nal is then applied to a series of 10 comparators; each of which is biased to a different comparison level by the resistor string. In the example illustrated, the resistor string is connected to the internal 1.25V reference voltage. In this case, for each 3 dB that the input signal increases, a comparator will switch on another indicating LED. This resistor divider can be con- nected between any 2 voltages, providing that they are at least 1.5V below V + and no lower than V−. INTERNAL VOLTAGE REFERENCE The reference is designed to be adjustable and develops a nominal 1.25V between the REF OUT (pin 7) and REF ADJ (pin 8) terminals. The reference voltage is impressed across program resistor R1 and, since the voltage is constant, a constant current I 1 then flows through the output set resistor R2 giving an output voltage of: 00510405 Since the 120 µA current (max) from the adjust terminal represents an error term, the reference was designed to minimize changes of this current with V + and load changes. For correct operation, reference load current should be be- tween 80 µA and 5 mA. Load capacitance should be less than 0.05 µF. CURRENT PROGRAMMING A feature not completely illustrated by the block diagram is the LED brightness control. The current drawn out of the reference voltage pin (pin 7) determines LED current. Ap- proximately 10 times this current will be drawn through each lighted LED, and this current will be relatively constant de- spite supply voltage and temperature changes. Current drawn by the internal 10-resistor divider, as well as by the external current and voltage-setting divider should be in- cluded in calculating LED drive current. The ability to modu- late LED brightness with time, or in proportion to input volt- age and other signals can lead to a number of novel displays or ways of indicating input overvoltages, alarms, etc. The LM3915 outputs are current-limited NPN transistors as shown below. An internal feedback loop regulates the tran- sistor drive. Output current is held at about 10 times the reference load current, independent of output voltage and processing variables, as long as the transistor is not satu- rated. LM3915 Output Circuit 00510406 Outputs may be run in saturation with no adverse effects, making it possible to directly drive logic. The effective satu- ration resistance of the output transistors, equal to R E plus the transistors’ collector resistance, is about 50 Ω. It’s also possible to drive LEDs from rectified AC with no filtering. To avoid oscillations, the LED supply should be bypassed with a 2.2 µF tantalum or 10 µF aluminum electrolytic capacitor. MODE PIN USE Pin 9, the Mode Select input, permits chaining of multiple LM3915s, and controls bar or dot mode operation. The following tabulation shows the basic ways of using this input. Other more complex uses will be illustrated in the applica- tions. Bar Graph Display: Wire Mode Select (pin 9) directly to pin 3(V + pin). Dot Display, Single LM3915 Driver: Leave the Mode Select pin open circuit. Dot Display, 20 or More LEDs: Connect pin 9 of the first driver in the series (i.e., the one with the lowest input voltage comparison points) to pin 1 of the next higher LM3915 driver. Continue connecting pin 9 of lower input drivers to pin 1 of higher input drivers for 30 or more LED displays. The last LM3915 driver in the chain will have pin 9 left open. All previous drivers should have a 20k resistor in parallel with LED #9 (pin 11 to V LED). Mode Pin Functional Description This pin actually performs two functions. Refer to the simpli- fied block diagram below. Block Diagram of Mode Pin Function 00510407 *High for bar www.national.com 8 |
Số phần tương tự - LM3915N |
|
Mô tả tương tự - LM3915N |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |