công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LM2437 bảng dữ liệu(PDF) 5 Page - National Semiconductor (TI) |
|
|
LM2437 bảng dữ liệu(HTML) 5 Page - National Semiconductor (TI) |
5 / 10 page Application Hints (Continued) OPTIMIZING TRANSIENT RESPONSE Referring to Figure 9, there are three components (R1, R2 and L1) that can be adjusted to optimize the transient re- sponse of the application circuit. Increasing the values of R1 and R2 will slow the circuit down while decreasing over- shoot. Increasing the value of L1 will speed up the circuit as well as increase overshoot. It is very important to use induc- tors with very high self-resonant frequencies, preferably above 300 MHz. Ferrite core inductors from J.W. Miller Mag- netics (part # 78FR56M) were used for optimizing the perfor- mance of the device in the NSC application board. The val- ues shown in Figure 9 can be used as a good starting point for the evaluation of the LM2437. The NSC demo board also has a position open to add a resistor in parallel with L1. This resistor can be used to help control overshoot. Using vari- able resistors for R1 and the parallel resistor will simplify finding the values needed for optimum performance in a given application. Once the optimum values are determined the variable resistors can be replaced with fixed values. EFFECT OF LOAD CAPACITANCE Figure 8 shows the effect of increased load capacitance on the speed of the device. This demonstrates the importance of knowing the load capacitance in the application. EFFECT OF OFFSET Figure 7 shows the variation in rise and fall times when the output offset of the device is varied from 40 to 50 V DC. The rise time shows a maximum variation relative to the center data point (45 V DC) of about 20%. The fall time shows a variation of about 5% relative to the center data point. THERMAL CONSIDERATIONS Figure 4 shows the performance of the LM2437 in the test circuit shown in Figure 2 as a function of case temperature. The figure shows that the rise time of the LM2437 increases by approximately 5% as the case temperature increases from 50˚C to 100˚C. This corresponds to a speed degrada- tion of 1% for every 10˚C rise in case temperature.There is a negligible change in fall time vs. temperature in the test cir- cuit. Figure 6 shows the maximum power dissipation of the LM2437 vs. Frequency when all three channels of the device are driving an 8 pF load with a 40 V p-p alternating one pixel on, one pixel off signal. The graph assumes a 72% active time (device operating at the specified frequency) which is typical in a monitor application. The other 28% of the time the device is assumed to be sitting at the black level (65V in this case). This graph gives the designer the information needed to determine the heat sink requirement for his appli- cation. The designer should note that if the load capacitance is increased the AC component of the total power dissipation will also increase. The LM2437 case temperature must be maintained below 100˚C. If the maximum expected ambient temperature is 70˚C and the maximum power dissipation is 6.2W (from Fig- ure 6, 50 MHz bandwidth) then a maximum heat sink thermal resistance can be calculated: This example assumes a capacitive load of 8 pF and no re- sistive load. TYPICAL APPLICATION A typical application of the LM2437 is shown in Figure 10. Used in conjunction with an LM1279, a complete video chan- nel from monitor input to CRT cathode can be achieved. Per- formance is ideal for 1024 x 768 resolution displays with pixel clock frequencies up to 100 MHz. Figure 10 is the sche- matic for the NSC demonstration board that can be used to evaluate the LM1279/2437 combination in a monitor. PC BOARD LAYOUT CONSIDERATIONS For optimum performance, an adequate ground plane, isola- tion between channels, good supply bypassing and minimiz- ing unwanted feedback are necessary. Also, the length of the signal traces from the preamplifier to the LM2437 and from the LM2437 to the CRT cathode should be as short as pos- sible. The following references are recommended: Ott, Henry W., “Noise Reduction Techniques in Electronic Systems”, John Wiley & Sons, New York, 1976. “Video Amplifier Design for Computer Monitors”, National Semiconductor Application Note 1013. Pease, Robert A., “Troubleshooting Analog Circuits”, Butterworth-Heinemann, 1991. Because of its high small signal bandwidth, the part may os- cillate in a monitor if feedback occurs around the video chan- nel through the chassis wiring. To prevent this, leads to the video amplifier input circuit should be shielded, and input cir- cuit wiring should be spaced as far as possible from output circuit wiring. NSC DEMONSTRATION BOARD Figure 11 shows the routing and component placement on the NSC LM1279/2437 demonstration board. The schematic of the board is shown in Figure 10. This board provides a DS100932-10 FIGURE 9. One Channel of the LM2437 with the Recommended Arc Protection Circuit www.national.com 5 |
Số phần tương tự - LM2437 |
|
Mô tả tương tự - LM2437 |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |