LM40 datasheet(10/27 Pages) NSC

tên linh kiện	LM40

Giải thích chi tiết về linh kiện	Hardware Monitor with Dual Thermal Diodes and SensorPath Bus

Download	27 Pages

Scroll/Zoom	100%

nhà sản xuất	NSC [National Semiconductor (TI)]

Trang chủ	http://www.national.com

Logo

10 / 27 page

Typical Performance Characteristics

Remote Diode Temperature Reading Sensitivity to Diode

Filter Capacitance

Thermal Diode Capacitor or PCB Leakage Current Effect

on Remote Diode Temperature Reading

20068421

20068422

1.0 Functional Description

The LM40 hardware monitor measures up to 3 temperature

zones and 5 power supply voltages. The LM40 uses a

∆V

be

temperature sensing method. A differential voltage, repre-

senting temperature, is digitized using a Sigma-Delta analog

to digital converter. Internal scaling resistors allow direct

measurement of the +1.6V, +2.5V, +5V, +3.3V and +12V

power supply inputs. The digitized data can be retrieved over

a simple single-wire interface called SensorPath. Sensor-

Path has been defined by National Semiconductor and is

optimized for hardware monitoring. National offers a royalty-

free license in connection with its intellectual property rights

in the SensorPath bus.

The LM40 has one address pin to allow up to two LM40s to

be connected to one SensorPath bus. The physical interface

of SensorPath’s SWD signal is identical to the familiar indus-

try standard SMBus SMBDAT signal. The digital information

is encoded in the pulse width of the signal being transmitted.

Every bit can be synchronized by the master simplifying the

implementation of the master when using a micro-controller.

For micro-controller’s with greater functionality an asynchro-

nous attention signal can be transmitted by the LM40 to

interrupt the micro-controller and notify it that temperature/

voltage data has been updated in the readout registers.

To optimize the LM40’s power consumption to the system

requirements, the LM40 has a shutdown mode and supports

multiple conversion rates.

1.1 SensorPath BUS SWD

SWD is the Single Wire Data line used for communication.

SensorPath uses 3.3V single-ended signaling, with a pull-up

resistor and open-drain low-side drive (see Figure 3). For

timing purposes SensorPath is designed for capacitive loads

(C

L) of up to 400pF. Note that in many cases a 3.3V standby

rail of the PC will be used as a power supply for both the

sensor and the master. Logic high and low voltage levels for

SWD are TTL compatible. The master may provide an inter-

nal pull-up resistor. In this case the external resistor is not

needed. The minimum value of the pull-up resistor must take

into account the maximum allowable output load current of

4mA.

1.2 SensorPath BIT SIGNALING

Signals are transmitted over SensorPath using pulse-width

encoding. There are five types of "bit signals":

•

Data Bit 0

•

Data Bit 1

•

Start Bit

•

Attention Request

•

Reset

All the "bit signals" involve driving the bus to a low level. The

duration of the low level differentiates between the different

"bit-signals". Each "bit signal" has a fixed pulse width. Sen-

sorPath supports a Bus Reset Operation and Clock Training

sequence that allows the slave device to synchronize its

internal clock rate to the master. Since the LM40 meets the

±15% timing requirements of SensorPath, the LM40 does

not require the Clock Training sequence and does not sup-

port this feature. This section defines the "bit signal" behav-

ior in all the modes. Please refer to the timing diagrams in

the Electrical Characteristics section (Figure 1 and Figure 2)

while going through this section. Note that the timing dia-

grams for the different types of "bit signals" are shown

together to better highlight the timing relationships between

them. However, the different types of "bit signals" appear on

SWD at different points in time. These timing diagrams show

the signals as driven by the master and the LM40 slave as

well as the signal as seen when probing SWD. Signal labels

20068407

FIGURE 3. SensorPath SWD simplified schematic

www.national.com

10

Số phần tương tự - LM40

nhà sản xuất	tên linh kiện	bảng dữ liệu	Giải thích chi tiết về linh kiện
SEMTECH ELECTRONICS LTD...	LM4001	280Kb / 2P	SURFACE MOUNT SILICON RECTIFIERS
Microdiode Electronics ...	LM4001	908Kb / 2P	SURFACE MOUNT RECTIFIERS
Microdiode Electronics ...	LM4001	505Kb / 2P	SURFACE MOUNT RECTIFIER
SEMTECH ELECTRONICS LTD...	LM4001G	281Kb / 2P	SURFACE MOUNT GLASS PASSIVATED SILICON RECTIFIERS
Formosa MS	LM4001G	254Kb / 2P	Surface Mount Glass Passivated Silicon Rectifiers

More results

Mô tả tương tự - LM40

nhà sản xuất	tên linh kiện	bảng dữ liệu	Giải thích chi tiết về linh kiện
National Semiconductor ...	LM41	367Kb / 27P	Hardware Monitor with Thermal Diode Inputs and SensorPath??Bus
	LM96011	80Kb / 2P	Hardware Monitor with Thermal Diode Input and SensorPath??Bus
	LM32	340Kb / 24P	Dual Thermal Diode Temperature Sensor with SensorPath Bus
ON Semiconductor	ADM1024	315Kb / 29P	System Hardware Monitor with Remote Diode Thermal Sensing April, 2012 ??Rev. 4
ON Semiconductor	ADM1024	256Kb / 30P	System Hardware Monitor with Remote Diode Thermal Sensing January, 2016 ??Rev. 5
Analog Devices	ADM1024	285Kb / 28P	System Hardware Monitor with Remote Diode Thermal Sensing REV. 0
Texas Instruments	LM95010	1Mb / 28P	[Old version datasheet] Digital Temperature Sensor with SensorPath Bus
ADL Embedded Solutions	ADLQM67PC-3517UE	877Kb / 3P	Hardware monitor with api
ADL Embedded Solutions	ADLQM67PC	829Kb / 3P	hardware monitor with api
Texas Instruments	TMP141	295Kb / 19P	[Old version datasheet] Digital Out Temperature Sensor with Single-Wire SensorPath Bus

More results

LM40 bảng dữ liệu(PDF) 10 Page - National Semiconductor (TI)

LM40 bảng dữ liệu(HTML) 10 Page - National Semiconductor (TI)

Số phần tương tự - LM40

Mô tả tương tự - LM40

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

bảng dữ liệu tải về

Link URL