công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LM4852ITL bảng dữ liệu(PDF) 6 Page - National Semiconductor (TI) |
|
|
LM4852ITL bảng dữ liệu(HTML) 6 Page - National Semiconductor (TI) |
6 / 21 page Electrical Characteristics 3.0V (Notes 2, 8) (Continued) The following specifications apply for V DD= 3.0V, TA= 25˚C unless otherwise specified. Symbol Parameter Conditions LM4852 Units (Limits) Typical (Note 5) Limits (Notes 6, 11) Digital Volume Range (R IN and LIN) Input referred minimum gain -40.5 -41.1 -39.9 dB (min) dB (max) Input referred maximum gain 6.0 5.4 6.6 dB (min) dB (max) Digital Volume Stepsize 1.5 dB Digital Volume Stepsize Error ±0.1 ±0.6 dB ( max) Phone In Volume BTL gain from Phone In to SPKR OUT 6 5.4 6.6 dB (min) dB (max) Mute Attenuation Output Mode 1, 3, 5 100 dB Phone In Input Impedance 20 15 25 k Ω (min) k Ω (max) R IN and LIN Input Impedance Maximum gain setting 30 22.5 37.5 k Ω (min) k Ω (max) Mininum gain setting 100 75 125 k Ω (min) k Ω (max) T SD Thermal Shutdown Temperature 170 150 ˚C (min) t 1 SCL (Clock) Period 2.5 µs (min) t 2 SDA to SCL Set-up Time 100 ns (min) t 3 Data Out Stable Time 0 ns (min) t 4 Start Condition Time 100 ns (min) t 5 Stop Condition Time 100 ns (min) Note 2: Absolute Maximum Rating indicate limits beyond which damage to the device may occur. Note 3: Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 4: Human body model, 100pF discharged through a 1.5k Ω resistor. Note 5: Typical specifications are specified at +25˚C and represent the most likely parametric norm. Note 6: Tested limits are guaranteed to National’s AOQL (Average Outgoing Quality Level). Note 7: Machine Model ESD test is covered by specification EIAJ IC-121-1981. A 200pF cap is charged to the specified voltage, then discharged directly into the IC with no external series resistor (resistance of discharge path must be under 50 Ω). Note 8: All voltages are measured with respect to the ground pin, unless otherwise specified. Note 9: The given θJA and θJC are for an LM4852 mounted on a demonstration board with a 4in2 area of 1oz printed circuit board copper ground plane. Note 10: Please refer to the Output Noise vs Output Mode table in the Typical Performance Characteristics section for more details. Note 11: Datasheet min/max specifications are guaranteed by design, test, or statistical analysis. www.national.com 6 |
Số phần tương tự - LM4852ITL |
|
Mô tả tương tự - LM4852ITL |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |