công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LM124QML bảng dữ liệu(PDF) 6 Page - Texas Instruments |
|
LM124QML bảng dữ liệu(HTML) 6 Page - Texas Instruments |
6 / 31 page LM124AQML, LM124QML SNOSAE0K – AUGUST 2004 – REVISED MARCH 2013 www.ti.com LM124/883 Electrical Characteristics SMD: 77043 DC Parameters (The following conditions apply to all the following parameters, unless otherwise specified.) All voltages referenced to device ground. Sub- Symbol Parameter Conditions Notes Min Max Unit Groups V+ = 5V 1.2 mA 1, 2, 3 ICC Power Supply Current 3.0 mA 1 V+ = 30V 4.0 mA 2, 3 V+ = 15V, VOUT = 200mV, 12 uA 1 +VIN = 0mV, -VIN = +65mV ISINK Output Sink Current V+ = 15V, VOUT = 2V, 10 mA 1 +VIN = 0mV, -VIN = +65mV 5 mA 2, 3 V+ = 15V, VOUT = 2V, -20 mA 1 ISOURCE Output Source Current +VIN = 0mV, -VIN = -65mV -10 mA 2, 3 IOS Short Circuit Current V+ = 5V, VOUT = 0V -60 mA 1 -5 5 mV 1 V+ = 30V, VCM = 0V -7 7 mV 2, 3 -5 5 mV 1 V+ = 30V, VCM = 28V VIO Input Offset Voltage -7 7 mV 2, 3 -5 5 mV 1 V+ = 5V, VCM = 0V -7 7 mV 2, 3 V+ = 30V, VCM = 28.5V -5 5 mV 1 Common Mode CMRR V+ = 30V, VIN = 0V to 28.5V (1) 70 dB 1 Rejection Ratio -150 10 nA 1 +IIB Input Bias Current V+ = 5V, VCM = 0V (2) -300 10 nA 2, 3 -30 30 nA 1 IIO Input Offset Current V+ = 5V, VCM = 0V -100 100 nA 2, 3 PSRR Power Supply Rejection V+ = 5V to 30V, VCM = 0V 65 dB 1 Ratio (3) 28.5 V 1 Common Mode Voltage VCM V+ = 30V (1) Range 28 V 2, 3 V+ = 15V, RL = 2K Ω, 50 V/mV 4 AVS Large Signal Gain VO = 1V to 11V 25 V/mV 5, 6 V+ = 30V, RL = 2K Ω 26 V 4, 5, 6 VOH Output Voltage High V+ = 30V, RL = 10K Ω 27 V 4, 5, 6 V+ = 30V, RL = 10K Ω 40 mV 4, 5, 6 40 mV 4 VOL Output Voltage Low V+ = 30V, ISINK = 1uA 100 mV 5, 6 V+ = 5V, RL= 10K Ω 20 mV 4, 5, 6 Channel Separation (4) 1KHz, 20KHz 80 dB 4 (Amp to Amp Coupling) (5) (1) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The upper end of the common-mode voltage range is V+ −1.5V (at 25°C), but either or both inputs can go to +32V without damage independent of the magnitude of V+. (2) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so no loading change exists on the input lines. (3) Specified by VIO tests. (4) Ensured, not tested (5) Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This typically can be detected as this type of capacitance increases at higher frequencies. 6 Submit Documentation Feedback Copyright © 2004–2013, Texas Instruments Incorporated Product Folder Links: LM124AQML LM124QML |
Số phần tương tự - LM124QML |
|
Mô tả tương tự - LM124QML |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |