công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
1--23147-2 bảng dữ liệu(PDF) 3 Page - Tyco Electronics |
|
1--23147-2 bảng dữ liệu(HTML) 3 Page - Tyco Electronics |
3 / 5 page 408- 6930 3 of 5 Rev F 3 — The contact beams are NOT deformed. If damage is apparent, replace the contacts in accordance with the instructions packaged with the connector. 4 — The wire insulation is NOT nicked or cut in any area other than the two contact slots. 5 — The wire extends past the wire retainer (strain relief) of the connector. 4. WIRE INSERTION DEPTH ADJUSTMENT (See Figure 4) 1. Remove the head from the handle assembly. 2. If the wire is inserted too deeply (more than the required wire insertion depth), reduce the wire insertion depth by turning the adjuster 1/6 of a revolution clockwise. The wire insertion depth will be reduced by approximately 0.20 mm [.008 in.]. If the wire is bottomed in the contact slot, this indicates that the adjuster is set to the maximum wire insertion depth — DO NOT turn the adjuster counterclockwise; otherwise damage to the head may occur. If the wire is not inserted deeply enough (less than the required wire insertion depth), increase the wire insertion depth by turning the adjuster 1/6 of a revolution counterclockwise. The wire insertion depth will be increased by approximately 0.20 mm [.008 in.]. When turning the adjuster counterclockwise, make sure to check the wire insertion depth after EACH 1/6 revolution. If the adjuster is set past the maximum setting, damage to the head may occur. Figure 4 Turn CLOCKWISE to Reduce Wire Insertion Depth Turn COUNTERCLOCKWISE to Increase Wire Insertion Depth DO NOT Turn Past Maximum Setting Refer to CAUTION Adjuster Wire Insertion Depth Adjustment Note: 1 /6 Revolution Equals 0.20 mm [.008 in.] Adjustment 5. TERMINATING PROCEDURE (Refer to Figure 5) There is no wire preparation required. 1. Insert the connector into the left side of the head. 2. Align the contact to be terminated with the wire inserter of the head (shown in Figure 1). Make sure that the locating pawl rests between the connector index ribs. 3. Insert an unstripped wire into the funnel area between the contact and the wire inserter until it bottoms on the tool base. 4. Squeeze the cam handle (manual) or depress the trigger (pneumatic) of the handle assembly, and hold it until the ratchet releases (manual) or the wire inserter bottoms (pneumatic). 5. Release the cam handle or trigger. The wire inserter will retract and the feed slide will automatically advance the connector to the next contact position. The locating pawl will move up and down as the connector is automatically advanced through the head. However, if movement is obstructed, or if desired, the locating pawl can be depressed and the connector moved manually out of the RIGHT side of the head. 6. Repeat Steps 2 through 5 until all contacts have been terminated. 7. Inspect each termination according to Paragraph 3.2. 6. MAINTENANCE AND INSPECTION 6.1. Daily Maintenance 1. Remove dust, moisture, and other contaminants with a clean, soft brush or lint--free cloth. DO NOT use objects that could damage the head. 2. Make sure that all components are in place and properly secured. 3. Actuate the tool to make sure that the mechanisms inside the head function smoothly. 6.2. Periodic Maintenance 1. Remove any accumulated film with a suitable cleaning agent that will not affect plastic. 2. Make sure all components are in place and properly secured. 3. Check for chipped, cracked, worn, or broken areas on the head. If damage is evident, repair or replace the head. CAUTION ! CAUTION ! NOTE i NOTE i |
Số phần tương tự - 1--23147-2 |
|
Mô tả tương tự - 1--23147-2 |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |