công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LM2662MX bảng dữ liệu(PDF) 9 Page - Texas Instruments |
|
LM2662MX bảng dữ liệu(HTML) 9 Page - Texas Instruments |
9 / 19 page LM2662, LM2663 www.ti.com SNVS002D – JANUARY 1999 – REVISED MAY 2013 The oscillator frequency can be lowered by adding an external capacitor between OSC and GND (See typical performance characteristics). Also, in the inverter mode, an external clock that swings within 100 mV of V+ and GND can be used to drive OSC. Any CMOS logic gate is suitable for driving OSC. LV must be grounded when driving OSC. The maximum external clock frequency is limited to 150 kHz. The switching frequency of the converter (also called the charge pump frequency) is half of the oscillator frequency. NOTE: OSC cannot be driven by an external clock in the voltage-doubling mode. Table 1. LM2662 Oscillator Frequency Selection FC OSC Oscillator Open Open 20 kHz V+ Open 150 kHz Open or V+ External Capacitor See Typical Performance Characteristics N/A External Clock (inverter mode only) External Clock Frequency Table 2. LM2663 Oscillator Frequency Selection OSC Oscillator Open 150 kHz External Capacitor See Typical Performance Characteristics External Clock (inverter mode only) External Clock Frequency SHUTDOWN MODE For the LM2663, a shutdown (SD) pin is available to disable the device and reduce the quiescent current to 10 μA. Applying a voltage greater than 2V to the SD pin will bring the device into shutdown mode. While in normal operating mode, the SD pin is connected to ground. CAPACITOR SELECTION As discussed in the Simple Negative Voltage Converter section, the output resistance and ripple voltage are dependent on the capacitance and ESR values of the external capacitors. The output voltage drop is the load current times the output resistance, and the power efficiency is (3) Where IQ(V+) is the quiescent power loss of the IC device, and IL 2R OUT is the conversion loss associated with the switch on-resistance, the two external capacitors and their ESRs. Low ESR capacitors (Table 3) are recommended for both capacitors to maximize efficiency, reduce the output voltage drop and voltage ripple. For convenience, C1 and C2 are usually chosen to be the same. The output resistance varies with the oscillator frequency and the capacitors. In Figure 19, the output resistance vs. oscillator frequency curves are drawn for four difference capacitor values. At very low frequency range, capacitance plays the most important role in determining the output resistance. Once the frequency is increased to some point (such as 100 kHz for the 47 μF capacitors), the output resistance is dominated by the ON resistance of the internal switches and the ESRs of the external capacitors. A low value, smaller size capacitor usually has a higher ESR compared with a bigger size capacitor of the same type. Ceramic capacitors can be chosen for their lower ESR. As shown in Figure 19, in higher frequency range, the output resistance using the 10 μF ceramic capacitors is close to these using higher value tantalum capacitors. Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 9 Product Folder Links: LM2662 LM2663 |
Số phần tương tự - LM2662MX |
|
Mô tả tương tự - LM2662MX |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |