![]() |
công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LZL1-6C bảng dữ liệu(PDF) 2 Page - Honeywell Accelerometers |
|
LZL1-6C bảng dữ liệu(HTML) 2 Page - Honeywell Accelerometers |
2 / 2 page ![]() PK 88142 SIDE ROTARY TYPE SIDE LEVER BRACKET TYPE PK 88142 CHANGING ACTUATION DIRECTION ON ROTARY TYPE Rotary switches may be adjusted to operate clockwise, counterclockwise, or both. Instruc- tions are cast into the head (Figure 4). Follow these steps: 1. Loosen the four captive head screws and remove head from switch housing. 2. Switches are assembled with the plunger set for both way operation. (See drawing Figure 4.) Both way actuation: plunger point in twelve o'clock position (towards the actuator). To change mode of operation pull the spring loaded plunger outward with pli- ers to the stop. With plunger, pulled turn the point in the direction of operation required. Clockwise actuation only: turn clock- wise to three o'clock position. Counterclockwise actuation only: turn counterclockwise to nine o'clock posi- tion. 3 . Release plunger, it will snap into the head into a locked position. 4 . Replace operating head on switch hous- ing and securely tighten screws. 5 . Check for desired operation by actuating switch and listening for "click". HEX HEAD SCREWS If you prefer to loosen and tighten the lever with a pliers or a screwdriver, a packet of 50 hex head screws, with screwdriver slot, is available separately (catalog listin g 15PA164-LS) to replace the allen head screw furnished with the lever. Adjusting tool set LSZ4005 consists of one special 3/32 inch open wrench and necessary hexagon key wrenches to adjust all types of levers. POSITIONING THE SIDE LEVER BRACKET The side lever bracket can be placed in any of four positions. When combined with the four possible head positions, this makes for 16 possible positions for this type. Remove the lever with a 5/32 inch hexagon key wrench. Loosen three captive bracket screws, place the bracket in the desired position, an d securely tighten the screws (refer to Figure 6). REVERSING THE ROLLER LEVER ARM Roller arms may be reversed to face the roller to the inside or outside of the arm (refer to Figure 7). It is recommended that the lever of side lever bracket forms be adjusted within the parameters shown in Figure 7. Use a 5/32 hexagon key wrench. WOBBLE STICK ACTUATOR TYPE REPLACING THE WOBBLE STICK To remove a wobble stick, firmly grasp the wobble stick with a pair of pliers at the base of the wobble stick. (Figure 8, View A.) Turn the wobble stick counterclockwise to unscrew it. To attach a wobble stick, start threading the actuator to the head by hand. Then firmly grasp the wobble stick with a pair of pliers as shown in Figure 8, View B. Turn the wobble stick clockwise to within 1/8 inch of the end of the threads. |
Số phần tương tự - LZL1-6C |
|
Mô tả tương tự - LZL1-6C |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |