công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
ADC0804-N bảng dữ liệu(PDF) 3 Page - Texas Instruments |
|
|
ADC0804-N bảng dữ liệu(HTML) 3 Page - Texas Instruments |
3 / 48 page ADC0801, ADC0802 ADC0803, ADC0804, ADC0805 www.ti.com SNOSBI1B – NOVEMBER 2009 – REVISED FEBRUARY 2013 OPERATING RATINGS (1) (2) over operating free-air temperature range (unless otherwise noted) Temperature Range TMIN ≤ TA ≤ TMAX ADC0804LCJ –40°C ≤ TA ≤ +85°C ADC0801/02/03/05LCN –40°C ≤ TA ≤ +85°C ADC0804LCN 0°C ≤ TA ≤ +70°C ADC0802/04LCWM 0°C ≤ TA ≤ +70°C Range of VCC 4.5 VDC to 6.3 VDC (1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its specified operating conditions. (2) All voltages are measured with respect to GND, unless otherwise specified. The separate A GND point should always be wired to the D GND. ELECTRICAL CHARACTERISTICS The following specifications apply for VCC = 5 VDC, TMIN ≤ TA ≤ TMAX and fCLK = 640 kHz (unless otherwise specified). PARAMETER CONDITIONS MIN TYP MAX UNITS ADC0801: Total Adjusted Error(1) With Full-Scale Adj. (See Full-Scale) ±1/4 LSB ADC0802: Total Unadjusted VREF/2=2.500 VDC ±1/2 LSB Error(1) ADC0803: Total Adjusted Error(1) With Full-Scale Adj.(See Full-Scale) ±1/2 LSB ADC0804: Total Unadjusted VREF/2=2.500 VDC ±1 LSB Error (1) ADC0805: Total Unadjusted VREF/2-No Connection ±1 LSB Error (1) ADC0801/02/03/05 2.5 8 VREF/2 Input Resistance (Pin 9) k Ω ADC0804 (2) 0.75 1.1 GND–0.0 Analog Input Voltage Range V(+) or V(–)(3) VCC+0.05 VDC 5 DC Common-Mode Error Over Analog Input Voltage Range ±1/16 ±1/8 LSB VCC=5 VDC ±10% Over Allowed VIN(+) and VIN(–) Voltage Power Supply Sensitivity ±1/16 ±1/8 LSB Range(3) (1) None of these A/Ds requires a zero adjust (see Zero Error). To obtain zero code at other analog input voltages see Errors and Reference Voltage Adjustments and Figure 51. (2) The VREF/2 pin is the center point of a two-resistor divider connected from VCC to ground. In all versions of the ADC0801, ADC0802, ADC0803, and ADC0805, and in the ADC0804LCJ, each resistor is typically 16 k Ω. In all versions of the ADC0804 except the ADC0804LCJ, each resistor is typically 2.2 k Ω. (3) For VIN(−)≥ VIN(+) the digital output code will be 0000 0000. Two on-chip diodes are tied to each analog input (see block diagram) which will forward conduct for analog input voltages one diode drop below ground or one diode drop greater than the VCC supply. Be careful, during testing at low VCC levels (4.5V), as high level analog inputs (5V) can cause this input diode to conduct–especially at elevated temperatures, and cause errors for analog inputs near full-scale. The spec allows 50 mV forward bias of either diode. This means that as long as the analog VIN does not exceed the supply voltage by more than 50 mV, the output code will be correct. To achieve an absolute 0 VDC to 5 VDC input voltage range will therefore require a minimum supply voltage of 4.950 VDC over temperature variations, initial tolerance and loading. Copyright © 2009–2013, Texas Instruments Incorporated Submit Documentation Feedback 3 Product Folder Links: ADC0801, ADC0802 ADC0803, ADC0804, ADC0805 |
Số phần tương tự - ADC0804-N |
|
Mô tả tương tự - ADC0804-N |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |