công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LM3241TLE/NOPB bảng dữ liệu(PDF) 13 Page - Texas Instruments |
|
|
LM3241TLE/NOPB bảng dữ liệu(HTML) 13 Page - Texas Instruments |
13 / 23 page High ECO Threshold ECO Mode at Light Load PWM Mode at Heavy Load Load current increases Low ECO Threshold Target Output Voltage LM3241 www.ti.com SNOSB38B – JANUARY 2009 – REVISED APRIL 2013 ECO Mode Operation At very light loads (50 mA to 100 mA), the LM3241 enters ECO mode operation with reduced switching frequency and supply current to maintain high efficiency. During ECO mode operation, the LM3241 positions the output voltage slightly higher (+7mV typ.) than the normal output voltage during PWM mode operation, allowing additional headroom for voltage drop during a load transient from light to heavy load. Figure 30. Operation in ECO Mode and Transfer to PWM Mode Shutdown Mode Setting the EN digital pin low (<0.4V) places the LM3241 in Shutdown mode (0.1 µA typ.). During shutdown, the PFET switch, the NFET synchronous rectifier, reference voltage source, control and bias circuitry of the LM3241 are turned off. Setting EN high (>1.2V) enables normal operation. EN should be set low to turn off the LM3241 during power-up and undervoltage conditions when the power supply is less than the 2.7V minimum operating voltage. The LM3241 has an UVLO (Under Voltage Lock Out) comparator to turn the power device off in the case the input voltage or battery voltage is too low. The typical UVLO threshold is around 2.0V for lock and 2.1V for release. Internal Synchronization Rectification While in PWM mode, the LM3241 uses an internal NFET as a synchronous rectifier to reduce rectifier forward voltage drop and associated power loss. Synchronous rectification provides a significant improvement in efficiency whenever the output voltage is relatively low compared to the voltage drop across an ordinary rectifier diode. With medium and heavy loads, the NFET synchronous rectifier is turned on during the inductor current down slope in the second part of each cycle. The synchronous rectifier is turned off prior to the next cycle. The NFET is designed to conduct through its intrinsic body diode during transient intervals before it turns on, eliminating the need for an external diode. Current Limiting The current limit feature allows the LM3241 to protect itself and external components during overload conditions. In PWM mode, the cycle-by-cycle current limit is 1450 mA (typ.). If an excessive load pulls the output voltage down to less than 0.3V (typ.), the NFET synchronous rectifier is disabled, and the current limit is reduced to 530 mA (typ.). Moreover, when the output voltage becomes less than 0.15V (typ.), the switching frequency will decrease to 3MHz, thereby preventing excess current and thermal stress. Copyright © 2009–2013, Texas Instruments Incorporated Submit Documentation Feedback 13 Product Folder Links: LM3241 |
Số phần tương tự - LM3241TLE/NOPB |
|
Mô tả tương tự - LM3241TLE/NOPB |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |