công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
TMP01 bảng dữ liệu(PDF) 10 Page - Analog Devices |
|
TMP01 bảng dữ liệu(HTML) 10 Page - Analog Devices |
10 / 20 page TMP01 Rev. E | Page 10 of 20 APPLICATIONS INFORMATION SELF-HEATING EFFECTS In some applications, the user should consider the effects of self-heating due to the power dissipated by the open-collector outputs, which are capable of sinking 20 mA continuously. Under full load, the TMP01 open-collector output device is dissipating PDISS = 0.6 V × .020A = 12 mW which in a surface-mount SOIC package accounts for a temperature increase due to self-heating of ΔT = PDISS × θJA = .012 W × 158°C/W = 1.9°C This self-heating effect directly affects the accuracy of the TMP01 and will, for example, cause the device to activate the OVER output 2 degrees early. Bonding the package to a moderate heat sink limits the self- heating effect to approximately: ΔT = PDISS × θJC = .012 W × 43°C/W = 0.52°C which is a much more tolerable error in most systems. The VREF and VPTAT outputs are also capable of delivering sufficient current to contribute heating effects and should not be ignored. BUFFERING THE VOLTAGE REFERENCE The reference output VREF is used to generate the temper- ature setpoint programming voltages for the TMP01 and also to determine the hysteresis temperature band by the reference load current IVREF. The on-board output buffer amplifier is typically capable of 500 μA output drive into as much as 50 pF load (maximum). Exceeding this load affects the accuracy of the reference voltage, could cause thermal sensing errors due to dissipation, and may induce oscillations. Selection of a low drift buffer functioning as a voltage follower with high input impedance ensures optimal reference accuracy, and does not affect the programmed hysteresis current. Amplifiers which offer the low drift, low power consumption, and low cost appropriate to this application include the OP295, and members of the OP90, OP97, OP177 families, and others as shown in the following applications circuits. With excellent drift and noise characteristics, VREF offers a good voltage reference for data acquisition and transducer excitation applications as well. Output drift is typically better than −10 ppm/°C, with 315 nV/√Hz (typ) noise spectral density at 1 kHz. PRESERVING ACCURACY OVER WIDE TEMPERATURE RANGE OPERATION The TMP01 is unique in offering both a wide range temper- ature sensor and the associated detection circuitry needed to implement a complete thermostatic control function in one monolithic device. While the voltage reference, setpoint comparators, and output buffer amplifiers have been carefully compensated to maintain accuracy over the specified temper- ature range, the user has an additional task in maintaining the accuracy over wide operating temperature ranges in the application. Since the TMP01 is both sensor and control circuit, in many applications it is possible that the external components used to program and interface the device may be subjected to the same temperature extremes. Thus, it may be necessary to locate components in close thermal proximity to minimize large temperature differentials, and to account for thermal drift errors, such as resistor matching tempcos, amplifier error drift, and the like, where appropriate. Circuit design with the TMP01 requires a slightly different perspective regarding the thermal behavior of electronic components. THERMAL RESPONSE TIME The time required for a temperature sensor to settle to a speci- fied accuracy is a function of the thermal mass of the sensor, and the thermal conductivity between the sensor and the object being sensed. Thermal mass is often considered equivalent to capacitance. Thermal conductivity is commonly specified using the symbol Q, and can be thought of as the reciprocal of thermal resistance. It is commonly specified in units of degrees per watt of power transferred across the thermal joint. Thus, the time required for the TMP01 to settle to the desired accuracy is dependent on the package selected, the thermal contact established in that particular application, and the equivalent power of the heat source. In most applications, the settling time is probably best determined empirically. |
Số phần tương tự - TMP01_09 |
|
Mô tả tương tự - TMP01_09 |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |