công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
MCP4652 bảng dữ liệu(PDF) 4 Page - Microchip Technology |
|
MCP4652 bảng dữ liệu(HTML) 4 Page - Microchip Technology |
4 / 102 page MCP453X/455X/463X/465X DS22096B-page 4 2008-2013 Microchip Technology Inc. AC/DC CHARACTERISTICS DC Characteristics Standard Operating Conditions (unless otherwise specified) Operating Temperature –40°C T A +125°C (extended) All parameters apply across the specified operating ranges unless noted. VDD = +2.7V to 5.5V, 5 k, 10 k, 50 k, 100 k devices. Typical specifications represent values for VDD = 5.5V, TA = +25°C. Parameters Sym Min Typ Max Units Conditions Supply Voltage VDD 2.7 — 5.5 V 1.8 — 2.7 V Serial Interface only. HVC pin Voltage Range VHV VSS —12.5V V VDD 4.5V The HVC pin will be at one of three input levels (VIL, VIH or VIHH). (Note 6) VSS —VDD + 8.0V VVDD < 4.5V VDD Start Voltage to ensure Wiper Reset VBOR — — 1.65 V RAM retention voltage (VRAM) < VBOR VDD Rise Rate to ensure Power-on Reset VDDRR (Note 9)V/ms Delay after device exits the reset state (VDD > VBOR) TBORD —10 20 µs Supply Current (Note 10) IDD — — 600 µA Serial Interface Active, HVC/A0 = VIH (or VIL) (Note 11) Write all 0’s to Volatile Wiper 0 VDD = 5.5V, FSCL = 3.4 MHz — — 250 µA Serial Interface Active, HVC/A0 = VIH (or VIL) (Note 11) Write all 0’s to Volatile Wiper 0 VDD = 5.5V, FSCL = 100 kHz — 2.5 5 µA Serial Interface Inactive, (Stop condition, SCL = SDA = VIH), Wiper = 0 VDD = 5.5V, HVC/A0 = VIH Note 1: Resistance is defined as the resistance between terminal A to terminal B. 2: INL and DNL are measured at VW with VA = VDD and VB = VSS. 3: MCP4XX1 only. 4: MCP4XX2 only, includes VWZSE and VWFSE. 5: Resistor terminals A, W and B’s polarity with respect to each other is not restricted. 6: This specification by design. 7: Non-linearity is affected by wiper resistance (RW), which changes significantly overvoltage and temperature. 8: The MCP4XX1 is externally connected to match the configurations of the MCP45X2 and MCP46X2, and then tested. 9: POR/BOR is not rate dependent. 10: Supply current is independent of current through the resistor network. 11: When HVC/A0 = VIHH, the IDD current is less due to current into the HVC/A0 pin. See IPU specification. |
Số phần tương tự - MCP4652 |
|
Mô tả tương tự - MCP4652 |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |