công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

AD569BD bảng dữ liệu(PDF) 6 Page - Analog Devices

tên linh kiện AD569BD
Giải thích chi tiết về linh kiện  16-Bit Monotonic Voltage Output D/A Converter
Download  12 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  AD [Analog Devices]
Trang chủ  http://www.analog.com
Logo AD - Analog Devices

AD569BD bảng dữ liệu(HTML) 6 Page - Analog Devices

Back Button AD569BD Datasheet HTML 2Page - Analog Devices AD569BD Datasheet HTML 3Page - Analog Devices AD569BD Datasheet HTML 4Page - Analog Devices AD569BD Datasheet HTML 5Page - Analog Devices AD569BD Datasheet HTML 6Page - Analog Devices AD569BD Datasheet HTML 7Page - Analog Devices AD569BD Datasheet HTML 8Page - Analog Devices AD569BD Datasheet HTML 9Page - Analog Devices AD569BD Datasheet HTML 10Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 6 / 12 page
background image
AD569
REV. A
–6–
Figure 5. Typical DNL at Segment Boundary Transitions
a. Segment 1
b. Segment 256
Figure 6. Typical DNL Within Segments
MULTIPLYING FEEDTHROUGH ERROR: This is the error
due to capacitive feedthrough from the reference to the output
with the input registers loaded with all zeroes.
FULL-SCALE ERROR: The AD569’s voltage dividing archi-
tecture gives rise to a fixed full-scale error which is independent
of the reference voltage. This error is trimmed by adjusting the
voltage applied to the +VREF terminals.
DIGITAL-TO-ANALOG GLITCH IMPULSE: The charge in-
jected into the analog output when a new input is latched into
the DAC register gives rise to the Digital-to-Analog Glitch
Impulse.
Glitches can be due to either time skews between the input bits
or charge injection from the internal switches. Glitch Impulse
for the AD569 is mainly due to charge injection, and is mea-
sured with the reference connections tied to ground. It is speci-
fied as the area of the glitch in nV-secs.
TOTAL ERROR: The worst-case Total Error is the sum of the
fixed full-scale and offset errors and the linearity error.
POWER SUPPLY AND REFERENCE VOLTAGE RANGES
The AD569 is specified for operation with
±12 volt power
supplies. With
±10% power supply tolerances, the maximum
reference voltage range is
±5 volts. Reference voltages up to
±6 volts can be used but linearity will degrade if the supplies
approach their lower limits of
±10.8 volts (12 volts - 10%).
If
±12 volt power supplies are unavailable in the system, several
alternative schemes may be used to obtain the needed supply
voltages. For example, in a system with
±15 V supplies, a single
Zener diode can be used to reduce one of the supplies to 9 volts
with the remaining one left at 15 volts. Figure 7a illustrates this
scheme. A 1N753A or equivalent diode is an appropriate choice
for the task. Asymmetrical power supplies can be used since the
AD569’s output is referenced to –VREF only and thus floats
relative to logic ground (GND, Pin 18). Assuming a worst-case
±1.5 volt tolerance on both supplies (10% of 15 volts), the
maximum reference voltage ranges would be +6 and –2 volts for
+VS = +15 V and VS = –9 V, and +2 to –8 volts for +VS = 9 V
and –VS = –15 V .
Alternately, two 3 V Zener diodes or voltage regulators can be
used to drop each
±15 volt supply to ±12 volts, respectively. In
Figure 7b, 1N746A diodes are a good choice for this task.
A third method may be used if both
±15 volt and ±5 volt sup-
plies are available. Figure 7c shows this approach. A combina-
tion of +VS = +15 V and –VS = –5 V can support a reference
range of 0 to 6 volts, while supplies of +VS = +5 V and –VS =
–15 V can support a reference range of 0 to –8 volts. Again,
10% power supply tolerances are assumed.
NOTE: Operation with +VS = +5 V alters the input latches’ op-
erating conditions causing minimum write pulse widths to ex-
tend to 1
µs or more. Control signals CS, HBE, LBE, and
LDAC
should, therefore, be tied low to render the latches trans-
parent.
No timing problems exist with operation at +VS = 9 V and
–VS = –15 V. However, 10% tolerances on these supplies gener-
ate a worst-case condition at –VS = –16.5 V and +VS = +7.5 V
(assuming +VS is derived from a +15 V supply). Under these
conditions, write pulse widths can stretch to 200 ns with similar
degradation of data setup and hold times. However,
±0.75 V
tolerances (
±5%) yield minimal effects on digital timing with
write pulse widths remaining below 100 ns.
Finally, Figure 7d illustrates the use of the combination of an
AD588 and AD569 in a system with
±15 volt supplies. As
shown, the AD588 is connected to provide
±5 V to the refer-
ence inputs of the AD569. It is doing double-duty by simulta-
neously regulating the supply voltages for the AD569 through
the use of the level shifting Zeners and transistors. This scheme
utilizes the capability of the outputs of the AD588 to source as
well as sink current. Two other benefits are realized by using
this approach. The first is that the AD569 is no longer directly
connected to the system power supplies. Output sensitivity to
variations in those supplies is, therefore, eliminated. The second


Số phần tương tự - AD569BD

nhà sản xuấttên linh kiệnbảng dữ liệuGiải thích chi tiết về linh kiện
logo
Analog Devices
AD569BD AD-AD569BD Datasheet
501Kb / 13P
   16-Bit Monotonic Voltage Output D/A Converter
More results

Mô tả tương tự - AD569BD

nhà sản xuấttên linh kiệnbảng dữ liệuGiải thích chi tiết về linh kiện
logo
Analog Devices
AD569KNZ AD-AD569KNZ Datasheet
433Kb / 12P
   16-Bit Monotonic Voltage Output D/A Converter
REV. A
AD569 AD-AD569_15 Datasheet
470Kb / 12P
   16-Bit Monotonic Voltage Output D/A Converter
REV. A
AD569 AD-AD569_17 Datasheet
501Kb / 13P
   16-Bit Monotonic Voltage Output D/A Converter
logo
Sipex Corporation
SP9501 SIPEX-SP9501 Datasheet
159Kb / 9P
   12-Bit, Voltage Output D/A Converter
logo
Analog Devices
DAC210FX AD-DAC210FX Datasheet
1Mb / 4P
   11-BIT VOLTAGE-OUTPUT D/A CONVERTER
7/89,Rev.B1
DAC210 AD-DAC210_15 Datasheet
1Mb / 4P
   11-BIT VOLTAGE OUTPUT D/A CONVERTER
logo
Sipex Corporation
SP9500 SIPEX-SP9500 Datasheet
157Kb / 9P
   12-Bit, Voltage Output D/A Converter
logo
Sanyo Semicon Device
LC7880M SANYO-LC7880M Datasheet
228Kb / 6P
   16 bit D/A CONVERTER
LC78866V SANYO-LC78866V Datasheet
138Kb / 6P
   16-bit A/D Converter?
LC78865M SANYO-LC78865M Datasheet
119Kb / 6P
   16-bit A/D Converter
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12


bảng dữ liệu tải về

Go To PDF Page


Link URL




Chính sách bảo mật
ALLDATASHEET.VN
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com