công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
AD2S82A bảng dữ liệu(PDF) 5 Page - Analog Devices |
|
AD2S82A bảng dữ liệu(HTML) 5 Page - Analog Devices |
5 / 16 page AD2S81A/AD2S82A REV. B –5– RECOMMENDED OPERATING CONDITIONS Power Supply Voltage (+VS to –VS) . . . . . . . . . ±12 V dc ±10% Power Supply Voltage VL . . . . . . . . . . . . . . . . . . +5 V dc ±10% Analog Input Voltage (SIN and COS) . . . . . . . . 2 V rms ±10% Analog Input Voltage (REF) . . . . . . . . . . . . . . 1 V to 8 V peak Signal and Reference Harmonic Distortion . . . . . . . 10% (max) Phase Shift Between Signal and Reference . ±10 Degrees (max) Ambient Operating Temperature Range Commercial (JD) . . . . . . . . . . . . . . . . . . . . . . 0 °C to +70°C Industrial (HP, JP, KP, LP) . . . . . . . . . . . . –40 °C to +85°C PIN FUNCTION DESCRIPTIONS Mnemonic Description REFERENCE I/P Reference Signal Input DEMOD I/P Demodulator Input AC ERROR O/P Ratio Multiplier Output COS I/P Cosine Input ANALOG GND Power Ground SIGNAL GND Resolver Signal Ground SIN I/P Sine Input +VS Positive Power Supply DB1–DB16 Parallel Output Data +VL Logic Power Supply ENABLE Logic Hi-Output Data in High Impedance State Logic Lo Present Data to the Output Latches BYTE SELECT Logic Hi-Most Significant Byte to DB1–DB8 Logic Lo-Most Significant Byte to DB1–DB8 INHIBIT Logic Lo Inhibits Data Transfer to Output Latches DIGITAL GND Digital Ground SC1–SC2* Select Converter Resolution DATA LOAD* Logic Lo DB1–DB16 Inputs Logic Hi DB1–DB16 Outputs BUSY Converter Busy, Data Not Valid While Busy Hi DIR Logic State Defines Direction of Input Signal Rotation RIPPLE CLK Positive Pulse when Converter Output Changes from 1s to All 0s or Vice Versa –VS Negative Power Supply VCO I/P VCO Input INTEGRATOR I/P Integrator Input INTEGRATOR O/P Integrator Output DEMOD O/P Demodulator Output COMPLEMENT* Active Logic Lo VCO O/P* VCO Output *AD2S82A Only. Bit Weight Table Binary Resolution Degrees Minutes Seconds Bits (N) (2N) /Bit /Bit /Bit 0 1 360.0 21600.0 1296000.0 1 2 180.0 10800.0 648000.0 2 4 90.0 5400.0 324000.0 3 8 45.0 2700.0 162000.0 4 16 22.5 1350.0 81000.0 5 32 11.25 675.0 40500.0 6 64 5.625 337.5 20250.0 7 128 2.8125 168.75 10125.0 8 256 1.40625 84.375 5062.5 9 512 0.703125 42.1875 2531.25 10 1024 0.3515625 21.09375 1265.625 11 2048 0.1757813 10.546875 632.8125 12 4096 0.0878906 5.273438 316.40625 13 8192 0.0439453 2.636719 158.20313 14 116384 0.0219727 1.318359 79.10156 15 32768 0.0109836 0.659180 39.55078 16 65536 0.0054932 0.329590 19.77539 17 131072 0.0027466 0.164795 9.88770 18 262144 0.0013733 0.082397 4.94385 ABSOLUTE MAXIMUM RATINGS 1 (with respect to GND) +VS 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +14 V dc –VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –14 V dc +VL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +VS Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +14 V to –VS SIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +14 V to –VS COS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +14 V to –VS Any Logical Input . . . . . . . . . . . . . . . . . . . –0.4 V dc to +VL dc Demodulator Input . . . . . . . . . . . . . . . . . . . . . . . +14 V to –VS Integrator Input . . . . . . . . . . . . . . . . . . . . . . . . . . +14 V to –VS VCO Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +14 V to –VS Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 860 mW Operating Temperature Commercial (JD) . . . . . . . . . . . . . . . . . . . . . . 0 °C to +70°C Industrial (HP, JP, KP, LP) . . . . . . . . . . . . . –40 °C to +85°C Storage Temperature (All Grades) . . . . . . . . . –65 °C to +150°C Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . +300 °C CAUTION 1. Absolute Maximum Ratings are those values beyond which damage to the device may occur. 2. Correct polarity voltages must be maintained on the +V S and –VS pins. AD2S81A/AD2S82A PIN CONFIGURATIONS REFERENCE I/P DEMOD I/P DEMOD O/P INTEGRATOR O/P ANALOG GND SIN I/P +VS –VS RIPPLE CLK DIR AC ERROR O/P COS I/P INTEGRATOR I/P VCO I/P MSB DB1 BUSY DB2 DIGITAL GND DB3 DB4 BYTE SELECT DB5 DB6 +VL DB7 DB8 LSB TOP VIEW (Not to Scale) 28 27 26 25 24 23 22 21 20 19 18 17 16 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 AD2S81A INHIBIT ENABLE 7 8 9 10 11 12 13 14 15 16 17 6 5 4 3 2 1 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 18 19 20 21 22 23 24 25 26 27 28 PIN 1 IDENTIFIER TOP VIEW (Not to Scale) NC = NO CONNECT –VS RIPPLE CLK DIR BUSY DATA LOAD COMPLEMENT SC2 SC1 DIGITAL GND INHIBIT NC SIN O/P +VS MSB DB1 NC DB2 DB3 DB4 DB5 DB6 DB7 DB8 AD2S82A |
Số phần tương tự - AD2S82A |
|
Mô tả tương tự - AD2S82A |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |