công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
AD1848 bảng dữ liệu(PDF) 7 Page - Analog Devices |
|
AD1848 bảng dữ liệu(HTML) 7 Page - Analog Devices |
7 / 28 page AD1848K REV. 0 –7– PIN DESCRIPTION Parallel Interface Pin Name PLCC TQFP I/O Description CDRQ 12 3 O Capture Data Request. The assertion of this signal indicates that the Codec has a cap- tured audio sample from the ADC ready for transfer. This signal will remain asserted un- til all the bytes from the capture buffer have been transferred. CDAK 11 2 I Capture Data Acknowledge. The assertion of this active LO signal indicates that the RD cycle occurring is a DMA read from the capture buffer. PDRQ 14 5 O Playback Data Request. The assertion of this signal indicates that the Codec is ready for more DAC playback data. The signal will remain asserted until all the bytes needed for a playback sample have been transferred. PDAK 13 4 I Playback Data Acknowledge. The assertion of this active LO signal indicates that the WR cycle occurring is a DMA write to the playback buffer. ADR1:0 9 & 10 1 & 64 I Codec Addresses. These address pins are asserted by the Codec interface logic during a control register/PIO access. The state of these address lines determine which register is accessed. RD 60 47 I Read Command Strobe. This active LO signal defines a read cycle from the Codec. The cycle may be a read from the control/PIO registers, or the cycles could be a read from the Codec’s DMA sample registers. WR 61 48 I Write Command Strobe. This active LO signal indicates a write cycle to the Codec. The cycle may be a write to the control/PIO registers, or the cycle could be a write to the Codec’s DMA sample registers. CS 59 46 I AD1848K Chip Select. The Codec will not respond to any control/PIO cycle accesses unless this active LO signal is LO. This signal is ignored during DMA transfers. DATA7:0 3–6 & 52–55 & I/O Data Bus. These pins transfer data and control information between the Codec and the 65–68 58–61 host. DBEN 63 50 O Data Bus Enable. This pin enables the external bus drivers. This signal is normally HI. For control register/PIO cycles, DBEN = (WR or RD) and CS For DMA cycles, DBEN = (WR or RD) and (PDAK or CDAK) DBDIR 62 49 O Data Bus Direction. This pin controls the direction of the data bus transceiver. HI enables writes from the host to the AD1848K; LO enables reads from the AD1848K to the host bus. This signal is normally HI. For control register/PIO cycles, DBDIR = RD and CS For DMA cycles, DBDIR = RD and (PDAK or CDAK) |
Số phần tương tự - AD1848 |
|
Mô tả tương tự - AD1848 |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |