3/7

www.rohm.com

○

c

2010 ROHM Co., Ltd. All rights reserved.

2010.02 - Rev.E

Data Sheet

TC Series P Case



Characteristics

Item

Performance

Test conditions (based on JIS C 5101

−1 and JIS C 5101−3)

Operating Temperature

−55

°C to +125°C

Maximum operating

temperature with no voltage

derating

+85

°C

Rated voltage (VDC)

20 25

16

10

6.3

4

Category voltage (VDC)

13 16

10

6.3

4

2.5

Surge voltage (VDC)

13

8

5.0

26

20

32

DC Leakage current

0.5

μA or 0.01CV whichever is greater

Shown in " Standard list "

Capacitance tolerance

Measuring frequency : 100±10kHz

Measuring voltage

: 0.5Vrms or less

Measuring circuit

: DC Equivalent series circuit

Tangent of loss angle

(Df, tan

δ)

Impedance

Resistance to

Soldering heat

Temperature

cycle

Moisture

resistance

There should be no significant abnormality.

The indications should be clear.

Appearance

ΔC / C

Df (tan

δ)

L.C.

Shall be satisfied the voltage on

" Standard list "

Measuring frequency : 120±12Hz

Measuring voltage

: 0.5Vrms

+1.5 to 2V.DC

Measuring circuit

: DC Equivalent series circuit

Shall be satisfied the voltage on

" Standard list "

at 85

°C

at 125

°C

at 85

°C

Voltage : Rated voltage for 1min

Shall be satisfied allowance range.

±

20%

Measuring frequency : 120±12Hz

Measuring voltage

: 0.5Vrms

+1.5 to 2V.DC

Measuring circuit

: DC Equivalent series circuit

Less than initial limit

Less than 150% of initial limit

Voltage reduction when temperature exceeds

+85

°C

As per 4.9 JIS C 5101-1

As per 4.5.1 JIS C 5101-3

As per 4.7 JIS C 5101-1

As per 4.5.2 JIS C 5101-3

As per 4.8 JIS C 5101-1

As per 4.5.3 JIS C 5101-3

As per 4.10 JIS C 5101-1

As per 4.5.4 JIS C 5101-3

As per 4.14 JIS C 5101-1

As per 4.6 JIS C 5101-3

Dip in the solder bath

Solder temp

: 260±10

°C

Duration

: 5±0.5s

Repetition

: 1

After the specimens, leave it at room temperature for

over 24h and then measure the sample.

As per 4.16 JIS C 5101-1

As per 4.10 JIS C 5101-3

As per 4.22 JIS C 5101-1

As per 4.12 JIS C 5101-3

TCP0G336M8R : Within

±20% of initial value

TCP0J226M8R : Within

±20% of initial value

TCP1A106M8R : Within

±20% of initial value

Others : Within

±10% of initial value

There should be no significant abnormality.

The indications should be clear.

Appearance

ΔC / C

Df (tan

δ)

L.C.

After leaving the sample under such atmospheric

condition that the temperature and humidity are

60

±2°C and 90 to 95% RH,respectiveiy, for 500±12h

leave it at room

temperature for over 24h and then measure the

sample.

Within

±20% of initial value

Less than 150%

of initial limit

There should be no significant abnormality.

The indications should be clear.

Appearance

ΔC / C

Df (tan

δ)

L.C.

Repetition : 5 cycles

(1 cycle : steps 1 to 4) without discontinuation.

Less than 150% of initial limit

TCP0J226M8R : Less than 150% of initial limit

TCP0G336M8R : Less than 150% of initial limit

Others

:

Less than initial limit

TCP0J226M8R : Less than 150% of initial limit

TCP0G336M8R : Less than 150% of initial limit

Others

:

Less than initial limit

TCP1A106M8R : Within

±20% of initial value

1 to 10

μF : Within ±10% of initial value

15 to 33

μF : Within ±20% of initial value

Temp.

Time

1

2

3

4

Room temp.

Room temp.

3min.or less

3min.or less

30

±3min.

30

±3min.

−55 3°C

+−

125 2

°C

+−

After the specimens, leave it at room temperature for

over 24h and then measure the sample.