công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
ISL22414UFU10Z bảng dữ liệu(PDF) 5 Page - Intersil Corporation |
|
ISL22414UFU10Z bảng dữ liệu(HTML) 5 Page - Intersil Corporation |
5 / 16 page 5 FN6424.1 December 16, 2010 IV-SB V- Current (Standby) V- = -5.5V, VCC = +5.5V @ +85°C, SPI interface in standby state -2.5 -0.7 µA V- = -5.5V, VCC = +5.5V @ +125°C, SPI interface in standby state -4 -3 µA V- = -2.25V, VCC = +2.25V @ +85°C, SPI interface in standby state -1.5 -0.3 µA V- = -2.25V, VCC = +2.25V @ +125°C, SPI interface in standby state -3 -1 µA ISD VCC Current (Shutdown) VCC = +5.5V, V- = -5.5V @ +85°C, SPI interface in standby state 0.2 1.5 µA VCC = +5.5V, V- = -5.5V @ +125°C, SPI interface in standby state 12.5 µA VCC = +2.25V, V- = -2.25V @ +85°C, SPI interface in standby state 0.1 1 µA VCC = +2.25V, V- = -2.25V @ +125°C, SPI interface in standby state 0.5 2 µA IV-SD V- Current (Shutdown) V- = -5.5V, VCC = +5.5V @ +85°C, SPI interface in standby state -2.5 -0.7 µA V- = -5.5V, VCC = +5.5V @ +125°C, SPI interface in standby state -4 -3 µA V- = -2.25V, VCC = +2.25V @ +85°C, SPI interface in standby state -1.5 -0.3 µA V- = -2.25V, VCC = +2.25V @ +125°C, SPI interface in standby state -3 -1 µA ILkgDig Leakage Current, at Pins SCK, SDI, SDO and CS Voltage at pin from GND to VCC -0.5 0.5 µA tWRT DCP Wiper Response Time CS rising edge to wiper new position 1.5 µs tShdnRec DCP Recall Time From Shutdown Mode CS rising edge to wiper stored position and RH connection 1.5 µs Vpor Power-on Recall Voltage Minimum VCC at which memory recall occurs 1.9 2.1 V VccRamp VCC Ramp Rate 0.2 V/ms tD Power-up Delay VCC above Vpor, to DCP Initial Value Register recall completed, and SPI Interface in standby state 5 ms EEPROM SPECIFICATION EEPROM Endurance 1,000,000 Cycles EEPROM Retention Temperature T ≤ +55ºC 50 Years tWC (Note 16) Non-volatile Write Cycle Time 12 20 ms SERIAL INTERFACE SPECIFICATIONS VIL SCK, SDI, and CS Input Buffer LOW voltage -0.3 0.3*VCC V VIH SCK, SDI, and CS Input Buffer HIGH Voltage 0.7*VCC VCC+0.3 V Hysteresis SCK, SDI, and CS Input Buffer Hysteresis 0.05*VCC V VOL SDO Output Buffer LOW Voltage IOL = 4mA for Open Drain output, pull-up voltage Vpu = VCC 00.4 V Operating Specifications Over the recommended operating conditions unless otherwise specified. Boldface limits apply over the operating temperature range. (Continued) SYMBOL PARAMETER TEST CONDITIONS MIN (Note 18) TYP (Note 4) MAX (Note 18) UNIT ISL22414 |
Số phần tương tự - ISL22414UFU10Z |
|
Mô tả tương tự - ISL22414UFU10Z |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |