công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
ISL22323UFV14Z bảng dữ liệu(PDF) 8 Page - Intersil Corporation |
|
ISL22323UFV14Z bảng dữ liệu(HTML) 8 Page - Intersil Corporation |
8 / 18 page 8 FN6422.1 March 13, 2008 Cb (Note 19) Capacitive Loading of SDA or SCL Total on-chip and off-chip 10 400 pF Rpu (Note 19) SDA and SCL Bus Pull-up Resistor Off-chip Maximum is determined by tR and tF For Cb = 400pF, max is about 2k Ω ~ 2.5kΩ For Cb = 40pF, max is about 15k Ω ~ 20kΩ 1k Ω tSU:A A0, A1, and A2 Setup Time Before START condition 600 ns tHD:A A0, A1, and A2 Hold Time After STOP condition 600 ns NOTES: 5. Typical values are for TA = +25°C and 3.3V supply voltage. 6. LSB: [V(RW)255 – V(RW)0]/255. V(RW)255 and V(RW)0 are V(RW) for the DCP register set to FF hex and 00 hex respectively. LSB is the incremental voltage when changing from one tap to an adjacent tap. 7. ZS error = V(RW)0/LSB. 8. FS error = [V(RW)255 – VCC]/LSB. 9. DNL = [V(RW)i – V(RW)i-1]/LSB-1, for i = 1 to 255. i is the DCP register setting. 10. INL = [V(RW)i – i • LSB – V(RW)0]/LSB for i = 1 to 255 11. VMATCH= [V(RWx)i -V(RWy)i]/LSB, for i = 0 to 255, x = 0 to 1, y = 0 to 1. 12. for i = 16 to 240 decimal, T = -40°C to +125°C. Max( ) is the maximum value of the wiper voltage and Min ( ) is the minimum value of the wiper voltage over the temperature range. 13. MI = |RW255 – RW0|/255. MI is a minimum increment. RW255 and RW0 are the measured resistances for the DCP register set to FF hex and 00 hex respectively. 14. ROFFSET = RW0/MI, when measuring between RW and RL. ROFFSET = RW255/MI, when measuring between RW and RH. 15. RDNL = (RWi – RWi-1)/MI -1, for i = 16 to 255. 16. RINL = [RWi – (MI • i) – RW0]/MI, for i = 16 to 255. 17. RMATCH= [(Rx)i -(Ry)i]/MI, for i = 0 to 255, x = 0 to 1, y = 0 to 1. 18. for i = 16 to 240, T = -40°C to +125°C. Max( ) is the maximum value of the resistance and Min ( ) is the minimum value of the resistance over the temperature range. 19. This parameter is not 100% tested. 20. tWC is the time from a valid STOP condition at the end of a Write sequence of I 2C serial interface, to the end of the self-timed internal non-volatile write cycle. 21. Parts are 100% tested at +25°C. Temperature limits established by characterization and are not production tested. Operating Specifications Over the recommended operating conditions unless otherwise specified. (Continued) SYMBOL PARAMETER TEST CONDITIONS MIN (Note 21) TYP (Note 5) MAX (Note 21) UNIT TC V Max V RW () i () Min V RW () i () – Max V RW () i () Min V RW () i () + [] 2 ⁄ ---------------------------------------------------------------------------------------------- 106 165°C ----------------- × = + TC R Max Ri () Min Ri () – [] Max Ri () Min Ri () + [] 2 ⁄ ---------------------------------------------------------------- 10 6 165°C ----------------- × = + ISL22323 |
Số phần tương tự - ISL22323UFV14Z |
|
Mô tả tương tự - ISL22323UFV14Z |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |