công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
TS321IDRE4 bảng dữ liệu(PDF) 4 Page - Texas Instruments |
|
TS321IDRE4 bảng dữ liệu(HTML) 4 Page - Texas Instruments |
4 / 11 page Electrical Characteristics TS321 SLOS489B – DECEMBER 2005 – REVISED SEPTEMBER 2008...................................................................................................................................... www.ti.com VCC+ = 5 V, VCC– = GND, VO = 1.4 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA MIN TYP MAX UNIT 25°C 0.5 4 RS = 0, 5 V < VCC+ < 30 V, VIO Input offset voltage mV 0 < VIC < (VCC+ – 1.5 V) Full range 5 25°C 2 30 IIO Input offset current nA Full range 50 25°C 20 150 IIB Input bias current(1) nA Full range 200 25°C 50 100 Large-signal differential voltage VCC = 15 V, RL = 2 kΩ, AVD V/mV amplification VO = 1.4 V to 11.4 V Full range 25 25°C 0 VCC+ – 1.5 VICR Common-mode input voltage(2) VCC = 30 V V Full range 0 VCC+ – 2 25°C 26 27 RL = 2 kΩ Full range 25.5 VCC = 30 V 25°C 27 28 VOH High-level output voltage RL = 10 kΩ V Full range 26.5 25°C 3.5 VCC = 5 V RL = 2 kΩ Full range 3 25°C 5 15 VOL Low-level output voltage RL = 10 kΩ V Full range 20 VCC = 30 V, VI = 10 mV, RL = 2 kΩ, GBP Gain bandwidth product 25°C 0.8 MHz f = 100 kHz, CL = 100 pF VCC = 15 V, VI = 0.5 V to 3 V, SR Slew rate 25°C 0.4 V/ µs RL = 2 kΩ, CL = 100 pF, unity gain φ m Phase margin 25°C 60 ° CMRR Common-mode rejection ratio RS ≤ 10 kΩ 25°C 65 85 dB ISOURCE Output source current VCC = 15 V, VO = 2 V, VID = 1 V 25°C 20 40 mA VO = 2 V 25°C 10 20 mA ISINK Output sink current VCC = 15 V, VID = 1 V VO = 0.2 V 25°C 12 50 µA IO Short-circuit to GND VCC = 15 V 25°C 40 60 mA SVR Supply-voltage rejection ratio VCC = 5 V to 30 V 25°C 65 110 dB VCC = 5 V 500 800 25°C VCC = 30 V 600 900 ICC Total supply current No load µA VCC = 5 V 600 900 Full range VCC = 30 V 1000 VCC = 30 V, VO = 2 Vpp, AV = 20 dB, THD Total harmonic distortion 25°C 0.015 % RL = 2 kΩ, f = 1 kHz, CL = 100 pF eN Equivalent input noise voltage VCC = 30 V, f = 1 kHz, RS = 100 Ω 25°C 50 nV/ √Hz (1) The direction of the input current is out of the device. This current essentially is constant, independent of the state of the output, so no loading change exists on the input lines. (2) The input common-mode voltage of either input signal should not be allowed to go negative by more than 0.3 V. The upper end of the common-mode voltage range is VCC+ – 1.5 V, but either or both inputs can go to 32 V without damage. 4 Submit Documentation Feedback Copyright © 2005–2008, Texas Instruments Incorporated Product Folder Link(s): TS321 |
Số phần tương tự - TS321IDRE4 |
|
Mô tả tương tự - TS321IDRE4 |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |