công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
MCF53016CMJ240 bảng dữ liệu(PDF) 7 Page - Freescale Semiconductor, Inc |
|
MCF53016CMJ240 bảng dữ liệu(HTML) 7 Page - Freescale Semiconductor, Inc |
7 / 62 page Hardware Design Considerations MCF5301x Data Sheet, Rev. 5 Preliminary—Subject to Change Without Notice Freescale Semiconductor 7 Figure 3. Supply Voltage Sequencing and Separation Cautions 3.3.1 Power Up Sequence If EVDD/SDVDD are powered up with the IVDD at 0V, then the sense circuits in the I/O pads will cause all pad output drivers connected to the EVDD/SDVDD to be in a high impedance state. There is no limit on how long after EVDD/SDVDD powers up before IVDD must power up. IVDD should not lead the EVDD, SDVDD or PVDD by more than 0.4V during power ramp up or there will be high current in the internal ESD protection diodes. The rise times on the power supplies should be slower than 1 microsecond to avoid turning on the internal ESD protection clamp diodes. The recommended power up sequence is as follows: 1. Use 1 microsecond or slower rise time for all supplies. 2. IVDD/PVDD and EVDD/SDVDD should track up to 0.9V and then separate for the completion of ramps with EVDD/SDVDD going to the higher external voltages. One way to accomplish this is to use a low drop-out voltage regulator. 3.3.2 Power Down Sequence If IVDD/PVDD are powered down first, then sense circuits in the I/O pads will cause all output drivers to be in a high impedance state. There is no limit on how long after IVDD and PVDD power down before EVDD or SDVDD must power down. IVDD should not lag EVDD, SDVDD, or PVDD going low by more than 0.4V during power down or there will be undesired high current in the ESD protection diodes. There are no requirements for the fall times of the power supplies. The recommended power down sequence is as follows: 1. Drop IVDD/PVDD to 0V. 2. Drop EVDD/SDVDD supplies. EVDD, USBVDD (3.3V) IVDD, PVDD Time 3.3V 1.2V 0 Notes: 1 IV DD should not exceed EVDD, SDVDD or PVDD by more than 0.4V at any time, including power-up. 2 Recommended that IV DD/PVDD should track EVDD/SDVDD up to 0.9V then separate for completion of ramps 3 Input voltage must not be greater than the supply voltage (EV DD, SDVDD, IVDD, or PVDD) by more than 0.5V at any time, including during power-up. 4 Use 1 microsecond or slower rise time for all supplies. 1 2 2.5V Supplies Stable SDVDD (2.5V - DDR) 1.8V SDVDD (1.8V - DDR) |
Số phần tương tự - MCF53016CMJ240 |
|
Mô tả tương tự - MCF53016CMJ240 |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |