công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
MCP652T bảng dữ liệu(PDF) 5 Page - Microchip Technology |
|
MCP652T bảng dữ liệu(HTML) 5 Page - Microchip Technology |
5 / 44 page © 2009 Microchip Technology Inc. DS22146A-page 5 MCP651/2/5 TABLE 1-3: DIGITAL ELECTRICAL SPECIFICATIONS Electrical Characteristics: Unless otherwise indicated, TA = 25°C, VDD = +2.5V to +5.5V, VSS = GND, VCM = VDD/2, VOUT ≈ VDD/2, VL = VDD/2, RL = 1 kΩ to VL, CL = 20 pF and CAL/CS =VSS (refer to Figure 1-1 and Figure 1-2). Parameters Sym Min Typ Max Units Conditions CAL/CS Low Specifications CAL/CS Logic Threshold, Low VIL VSS —0.2VDD V CAL/CS Input Current, Low ICSL —0— nA CAL/CS = 0V CAL/CS High Specifications CAL/CS Logic Threshold, High VIH 0.8VDD VDD V CAL/CS Input Current, High ICSH — 0.7 — µA CAL/CS = VDD GND Current ISS -3.5 -1.8 — µA Single, CAL/CS = VDD = 2.5V ISS -8 -4 — µA Single, CAL/CS = VDD = 5.5V ISS -5 -2.5 — µA Dual, CAL/CS = VDD = 2.5V ISS -10 -5 — µA Dual, CAL/CS = VDD = 5.5V CAL/CS Internal Pull Down Resistor RPD —5— M Ω Amplifier Output Leakage IO(LEAK) — 50 — nA CAL/CS = VDD POR Dynamic Specifications VDD Low to Amplifier Off Time (output goes High-Z) tPOFF — 200 — ns G = +1 V/V, VL = VSS, VDD = 2.5V to 0V step to VOUT = 0.1 (2.5V) VDD High to Amplifier On Time (including calibration) tPON 100 200 300 ms G = +1 V/V, VL = VSS, VDD = 0V to 2.5V step to VOUT = 0.9 (2.5V) CAL/CS Dynamic Specifications CAL/CS Input Hysteresis VHYST — 0.25 — V CAL/CS Setup Time (between CAL/CS edges) tCSU 1— — µs G = +1 V/V, VL = VSS (Notes 2, 3) CAL/CS = 0.8VDD to VOUT = 0.1 (VDD/2) CAL/CS High to Amplifier Off Time (output goes High-Z) tCOFF — 200 — ns G = +1 V/V, VL = VSS, CAL/CS = 0.8VDD to VOUT = 0.1 (VDD/2) CAL/CS Low to Amplifier On Time (including calibration) tCON —3 4 ms G = +1 V/V, VL = VSS, CAL/CS = 0.2VDD to VOUT = 0.9 (VDD/2) Note 1: The MCP652 has its CAL/CS input internally pulled down to VSS (0V). 2: This time ensures that the internal logic recognizes the edge. However, for the rising edge case, if CAL/CS is raised before the calibration is complete, the calibration will be aborted and the part will return to low power mode. 3: For the MCP655 dual, there is an additional constraint. CALA/CSA and CALB/CSB can be toggled simultaneously (within a time much smaller than tCSU) to make both op amps perform the same function simultaneously. If they are tog- gled independently, then CALA/CSA (CALB/CSB) cannot be allowed to toggle while op amp B (op amp A) is in calibration mode; allow more than the maximum tCON time (4 ms) before the other side is toggled. TABLE 1-4: TEMPERATURE SPECIFICATIONS Electrical Characteristics: Unless otherwise indicated, all limits are specified for: VDD = +2.5V to +5.5V, VSS = GND. Parameters Sym Min Typ Max Units Conditions Temperature Ranges Specified Temperature Range TA -40 — +125 °C Operating Temperature Range TA -40 — +125 °C (Note 1) Storage Temperature Range TA -65 — +150 °C Thermal Package Resistances Thermal Resistance, 8L-3×3 DFN θJA —63— °C/W (Note 2) Thermal Resistance, 8L-SOIC θJA — 163 — °C/W Note 1: Operation must not cause TJ to exceed Maximum Junction Temperature specification (150°C). 2: Measured on a standard JC51-7, four layer printed circuit board with ground plane and vias. |
Số phần tương tự - MCP652T |
|
Mô tả tương tự - MCP652T |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |