công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
FIN212ACBFX bảng dữ liệu(PDF) 10 Page - Fairchild Semiconductor |
|
FIN212ACBFX bảng dữ liệu(HTML) 10 Page - Fairchild Semiconductor |
10 / 23 page © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FIN212AC Rev. 1.0.6 10 Application Diagrams (Continued) G5 G6 C1 B5 A6 B3:E1 E2 F1 F2 G1 F6 G3 G4 SYS CLK /WE Baseband Microprocessor /RES VDDP VDDS/A CKREF STROBE DIRI PLL1 PLL0 DATA[7:0] CKP DP[8:1] DP[9] A0 DP[11] DP[12] DP[10] VDDS/A VDDP VDD1 VDD1 VDD2 C5 C6 D6 D5 E6 E5 B6 E5 E6 D6 D5 C6 C5 B6 A6 B5 C1 B3:E1 E2 F1 F2 G1 F6 G3 G4 D3 E4 F4 E4 F4 D3 2.775 S1 S0 LCD Primary Display FIN212 Serializer FIN212 Deserializer CKP STROBE CKREF DP[8:1] DP[9] DP[10] DP[11] DP[12] DIRI PWS1 PWS0 S1 S0 /WE DATA[7:0] C/D- /CS /RES NC NC NC NC NC NC NC NC G5 G6 LCD Sub Display /CS0 /CS1 VDD2 /WE DATA[7:0] C/D- /CS /RES CKSO+ CKSO- DSO+/DSI- DSO-/DSI+ CKSI - CKSI+ /DIRO CKSI+ CKSI- DSO-/DSI+ DSO+/DSI- CKSO- CKSO+ /DIRO VDD Figure 6. Dual Display with 8-Bit WRITE-Only Microcontroller Interface (Example Shows BGA 42-Pin Package) Serializer Configuration: PLL Frequency Mode: MODE 1 (S1=0, S0=1) CKREF=26MHz STROBE Frequency = 10 MHz PLL Divide Mode: Divide-by 2 (PLL1=1, PLL0=0) Multiplier x 3.5 Deserializer Configuration: Edge Rate Mode: SLOW MODE 1 (S1=1, S0=0) Pulse Width Mode: 13-Bit Time Mode (PWS1=PWS0=0) (~71.4ns) Additional Application Information Flex Cabling: The serial I/O information is transmitted at a high serial rate. Care must be taken implementing this serial I/O flex cable. The following best practices should be used when developing the flex cabling or Flex PCB. Keep all four differential Serial Wires the same length. Do not allow noisy signals over or near differential serial wires. Example: No LVCMOS traces over differential serial wires. Use only one ground plane or wire over the differential serial wires. Do not run ground over top and bottom. Design goal of 100-ohms differential characteristic impedance. Do not place test points on differential serial wires. Use differential serial wires a minimum of 2cm away from the antenna. For additional applications notes or flex guidelines see your sales rep or contact Fairchild directly. |
Số phần tương tự - FIN212ACBFX |
|
Mô tả tương tự - FIN212ACBFX |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |