công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
M27C160-90XF1 bảng dữ liệu(PDF) 8 Page - STMicroelectronics |
|
M27C160-90XF1 bảng dữ liệu(HTML) 8 Page - STMicroelectronics |
8 / 26 page Device description M27C160 8/26 2 Device description Table 2 lists the operating modes of the M27C160. A single power supply is required in the read mode. All inputs are TTL compatible except for VPP and 12V on A9 for the Electronic Signature. Note: X = V IH or VIL, VID = 12V ± 0.5V. 2.1 Read mode The M27C160 has two organisations, Word-wide and Byte-wide. The organisation is selected by the signal level on the BYTEVPP pin. When BYTEVPP is at VIH the Word-wide organisation is selected and the Q15A–1 pin is used for Q15 Data Output. When the BYTEVPP pin is at VIL the Byte-wide organisation is selected and the Q15A–1 pin is used for the Address Input A–1. When the memory is logically regarded as 16 bit wide, but read in the Byte-wide organisation, then with A–1 at VIL the lower 8 bits of the 16 bit data are selected and with A–1 at VIH the upper 8 bits of the 16 bit data are selected. The M27C160 has two control functions, both of which must be logically active in order to obtain data at the outputs. In addition the Word-wide or Byte- wide organisation must be selected. Chip Enable (E) is the power control and should be used for device selection. Output Enable (G) is the output control and should be used to gate data to the output pins independent of device selection. Assuming that the addresses are stable, the address access time (tAVQV) is equal to the delay from E to output (tELQV). Data is available at the output after a delay of tGLQV from the falling edge of G, assuming that E has been low and the addresses have been stable for at least tAVQV-tGLQV. 2.2 Standby mode The M27C160 has a standby mode which reduces the active current from 50mA to 100µA. The M27C160 is placed in the standby mode by applying a CMOS high signal to the E input. Table 2. Operating Modes Mode E G BYTEVPP A9 Q15A–1 Q8-Q14 Q7-Q0 Read Word-wide VIL VIL VIH X Data Out Data Out Data Out Read Byte-wide Upper VIL VIL VIL XVIH Hi-Z Data Out Read Byte-wide Lower VIL VIL VIL XVIL Hi-Z Data Out Output Disable VIL VIH X X Hi-Z Hi-Z Hi-Z Program VIL Pulse VIH VPP X Data In Data In Data In Verify VIH VIL VPP X Data Out Data Out Data Out Program Inhibit VIH VIH VPP X Hi-Z Hi-Z Hi-Z Standby VIH X X X Hi-Z Hi-Z Hi-Z Electronic Signature VIL VIL VIH VID Code Codes Codes |
Số phần tương tự - M27C160-90XF1 |
|
Mô tả tương tự - M27C160-90XF1 |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |