công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
STLC5046 bảng dữ liệu(PDF) 6 Page - STMicroelectronics |
|
STLC5046 bảng dữ liệu(HTML) 6 Page - STMicroelectronics |
6 / 27 page N. Name Type Function 28 CS0/GX0 DO/DI MCU control mode: CS0. Slic CS control #0. Depending on CONF reg. content can be a CS output for SLIC #0 or a static I/O. When configured as CS output it is automatically generated by the Codec with a repetition time of 31.25 µs. In this mode also the IO11..0 are synchronized and carry proper data in and out synchronous with CS. Pin-strap control mode: GX0. Transmit gain programming channel 0: 1: Transmit gain = 0dB 0: Transmit gain = - 3.5dB 29 CS1/GX1 DO/DI MCU control mode: CS1: Slic CS control #1, (see CS0 description). Pin-strap control mode: GX1. Transmit gain programming channel 1 (see GX0 description) 53 CS2/GX2 DO/DI MCU control mode: CS2. Slic CS control #2, (see CS0 description). Pin-strap control mode: GX2. Transmit gain programming channel 2 (see GX0 description) 52 CS3/GX3 DO/DI MCU control mode: CS3. Slic CS control #3, (see CS0 description). Pin-strap control mode: GX3. Transmit gain programming channel 3 (see GX0 description) 4 CS/PD1 DI/DI MCU control mode: CS. Chip Select of Serial Control Bus. When this pin is low control information can be written to or read from the device via the CI and CO pins. Pin-strap control mode: PD1. Power Down command channel 1. (see PD2 description). 7 CCLK/GR1 DI/DI MCU control mode: CCLK. Clock of Serial Control Bus. This clock shifts serial control ilnformation into or out of CI or CO when CS input is low depending on the current instruction. CCLK may be asyncronous with the other system clocks. Pin-strap control mode: GR1. Receive gain programming ch. 1, (see GR2 description). 6 CI/PD0 DI/DI MCU control mode: CI. Control Data Input of Serial Control Bus. Control data is shifted in the device when CS is low and clocked by CCLK. Pin-strap control mode: PD0. Power Down command channel 0. (see PD2 description). 5 CO/GR0 DTO/DI MCU control mode: CO. Control Data Output of Serial Control Bus. Control data is shifted out the device when CS is low and clocked by CCLK. During the first 8 CCLK pulses the CO pin is H. I., valid data are shifted out during the following 8 CCLK pulses. Pin-strap control mode: GR0. Receive gain programming ch. 0, (see GR2 description). 3 INT/AMU ODO/DI MCU control mode: INT. Interrupt output (open drain), goes low when a data change has been detected in the I/O pins. One mask registers allow to mask any I/O pin. Interrupt is reset when the I/O register is read. Pin-strap control mode: AMU. A/ µ law selection: AMU=0: µ law AMU=1: A law, even bit inverted PIN DESCRIPTION (continued) STLC5046 6/27 |
Số phần tương tự - STLC5046 |
|
Mô tả tương tự - STLC5046 |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |