công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
M27128AF6 bảng dữ liệu(PDF) 3 Page - STMicroelectronics |
|
M27128AF6 bảng dữ liệu(HTML) 3 Page - STMicroelectronics |
3 / 10 page For the most efficient use of these two control lines, E should be decoded and used as the primary device selecting function, while G should be made a common connection to all devices in the array and connected to the READ line from the system control bus. This ensures that all deselected memory devices are in their low power standby mode and that the output pins are only active when data is required from a particular memory device. System Considerations The power switching characteristics of fast EPROMs require careful decoupling of the devices. The supply current, ICC, has three segments that are of interest to the system designer: the standby current level, the active current level, and transient current peaks that are produced by the falling and rising edges of E. The magnitude of this transient current peaks is dependent on the capacitive and inductive loading of the device at the output. The associated transient voltage peaks can be sup- pressed by complying with the two line output control and by properly selected decoupling ca- pacitors. It is recommended that a 1 µF ceramic capacitor be used on every device between VCC and VSS. This should be a high frequency capacitor of low inherent inductance and should be placed as close to the device as possible. In addition, a 4.7 µF bulk electrolytic capacitor should be used between VCC and GND for every eight devices. The bulk capacitor should be located near the power supply connection point. The purpose of the bulk capacitor is to overcome the voltage drop caused by the inductive effects of PCB traces. Programming When delivered (and after each erasure for UV EPPROM), all bits of the M27128A are in the “1" state. Data is introduced by selectively program- ming ”0s" into the desired bit locations. Although only “0s” will be programmed, both “1s” and “0s” can be present in the data word. The only way to change a “0" to a ”1" is by ultraviolet light erasure. The M27128A is in the programming mode when VPP input is at 12.5V and E and P are at TTL low. The data to be programmed is applied 8 bits in parallel, to the data output pins. The levels required for the address and data inputs are TTL. Fast Programming Algorithm Fast Programming Algorithm rapidly programs M27128A EPROMs using an efficient and reliable method suited to the production programming en- vironment. Programming reliability is also ensured as the incremental program margin of each byte is Mode E G PA9 VPP Q0 - Q7 Read VIL VIL VIH XVCC Data Out Output Disable VIL VIH VIH XVCC Hi-Z Program VIL VIH VIL Pulse X VPP Data In Verify VIL VIL VIH XVPP Data Out Program Inhibit VIH XXX VPP Hi-Z Standby VIH XXX VCC Hi-Z Electronic Signature VIL VIL VIH VID VCC Codes Out Note: X = VIH or VIL, VID = 12V ± 0.5%. Table 3. Operating Modes Identifier A0 Q7 Q6 Q5 Q4 Q3 Q2 Q1 Q0 Hex Data Manufacturer’s Code VIL 00100 00 0 20h Device Code VIH 10001 00 1 89h Table 4. Electronic Signature DEVICE OPERATION (cont’d) 3/10 M27128A |
Số phần tương tự - M27128AF6 |
|
Mô tả tương tự - M27128AF6 |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |