 |
công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
|
công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
AD9879 bảng dữ liệu(PDF) 10 Page - Analog Devices |
|
||||||||||||||||||||||||||||||
AD9879 bảng dữ liệu(HTML) 10 Page - Analog Devices |
|
|
10 / 32 page  AD9879 Rev. A | Page 10 of 32 TERMINOLOGY Aperture Delay The aperture delay is a measure of the sample-and-hold amplifier (SHA) performance. It specifies the time delay between the rising edge of the sampling clock input and when the input signal is held for conversion. Aperture Uncertainty (Jitter) Aperture jitter is the variation in aperture delay for successive samples. It is manifested as noise on the input to the ADC. Channel-to-Channel Isolation (Crosstalk) In an ideal multichannel system, the signal in one channel does not influence the signal level of another channel. The channel- to-channel isolation specification is a measure of the change that occurs to a grounded channel as a full-scale signal is applied to another channel. Differential Nonlinearity Error (DNL, No Missing Codes) An ideal converter exhibits code transitions that are exactly 1 LSB apart. DNL is the deviation from this ideal value. Guaranteed no missing codes to 10-bit resolution indicates that all 1,024 codes, respectively, must be present over all operating ranges. Effective Number of Bits (ENOB) For a sine wave, SINAD can be expressed in terms of the number of bits. Using the formula N = (SINAD − 1.76 dB∕6.02) it is possible to determine a measure of performance expressed as N, the effective number of bits. Thus, the effective number of bits for a device’s sine wave inputs at a given input frequency can be calculated directly from its measured SINAD. Gain Error The first code transition should occur at an analog value 1/2 LSB above full scale. The last transition should occur for an analog value 1 1/2 LSB below the nominal full scale. Gain error is the deviation of the actual difference between the first and last code transitions and the ideal difference between the first and last code transitions. Input Referred Noise The rms output noise is measured using histogram techniques. The standard deviation of the ADC output code is calculated in LSB and converted to an equivalent voltage. This results in a noise figure that can be directly referred to the input of the MxFE. Integral Nonlinearity Error (INL) Linearity error refers to the deviation of each individual code from a line drawn from negative full scale through the positive full scale. The point used as the negative full scale occurs 1/2 LSB before the first code transition. Positive full scale is defined as a level 1 1/2 LSB beyond the last code transition. The deviation is measured from the middle of each code to the true straight line. Offset Error First transition should occur for an analog value 1/2 LSB above −FS. Offset error is defined as the deviation of the actual transition from that point. Output Compliance Range The range of allowable voltage at the output of a current-output DAC. Operation beyond the maximum compliance limits can cause either output stage saturation or break down, resulting in nonlinear performance. Phase Noise Single-sideband phase noise power is specified relative to the carrier (dBc/Hz) at a given frequency offset (1 kHz) from the carrier. Phase noise can be measured directly in single-tone transmit mode with a spectrum analyzer that supports noise marker measurements. It detects the relative power between the carrier and the offset (1 kHz) sideband noise and takes the resolution bandwidth (RBW) into account by subtracting 10 log(RBW). It also adds a correction factor that compensates for the implementation of the resolution bandwidth, log display, and detector characteristic. Pipeline Delay (Latency) Pipeline delay is the number of clock cycles between conversion initiation and the availability of the associated output data. Power Supply Rejection Power supply rejection specifies the converter’s maximum full- scale change when the supplies are varied from nominal to minimum and maximum specified voltages. Signal-to-Noise and Distortion (SINAD) Ratio SINAD is the ratio of the rms value of the measured input signal to the rms sum of all other spectral components below the Nyquist frequency, including harmonics but excluding dc. The value for SINAD is expressed in decibels. Signal-to-Noise Ratio (SNR) SNR is the ratio of the rms value of the measured input signal to the rms sum of all other spectral components below the Nyquist frequency, excluding harmonics and dc. The value for SNR is expressed in decibels. Spurious-Free Dynamic Range (SFDR) SFDR is the difference, in dB, between the rms amplitude of the DAC output signal (or the ADC input signal) and the peak spurious signal over the specified bandwidth (Nyquist bandwidth, unless otherwise noted). Total Harmonic Distortion (THD) THD is the ratio of the rms sum of the first six harmonic components to the rms value of the measured input signal, and is expressed as a percentage or in decibels. |
Số phần tương tự - AD9879_05 |
|
Mô tả tương tự - AD9879_05 |
|
|
Link URL |
| Chính sách bảo mật |
| ALLDATASHEET.VN |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Vietnamese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
