công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
74ALVTH16827VRG4 bảng dữ liệu(PDF) 4 Page - Texas Instruments |
|
74ALVTH16827VRG4 bảng dữ liệu(HTML) 4 Page - Texas Instruments |
4 / 16 page SN54ALVTH16827, SN74ALVTH16827 2.5-V/3.3-V 20-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCES076E – JULY 1996 – REVISED DECEMBER 1998 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 electrical characteristics over recommended operating free-air temperature range, VCC = 2.5 V ± 0.2 V (unless otherwise noted) PARAMETER TEST CONDITIONS SN54ALVTH16827 SN74ALVTH16827 UNIT PARAMETER TEST CONDITIONS MIN TYP† MAX MIN TYP† MAX UNIT VIK VCC = 2.3 V, II = –18 mA –1.2 –1.2 V VCC = 2.3 V to 2.7 V, IOH = –100 µA VCC–0.2 VCC–0.2 VOH VCC =2 3V IOH = –6 mA 1.8 V VCC = 2.3 V IOH = –8 mA 1.8 VCC = 2.3 V to 2.7 V, IOL = 100 µA 0.2 0.2 IOL = 6 mA 0.4 0.47 VOL VCC =2 3V IOL = 8 mA 0.4 V VCC = 2.3 V IOL = 18 mA 0.5 IOL = 24 mA 0.5 Control inputs VCC = 2.7 V, VI = VCC or GND ±1 ±1 Control inputs VCC = 0 or 2.7 V, VI = 5.5 V 10 10 II VI = 5.5 V 10 10 µA Data inputs VCC = 2.7 V VI = VCC 1 1 VI = 0 –5 –5 Ioff VCC = 0, VI or VO = 0 to 4.5 V ±100 µA IBHL‡ VCC = 2.3 V, VI = 0.7 V 115 115 µA IBHH§ VCC = 2.3 V, VI = 1.7 V –10 –10 µA IBHLO¶ VCC = 2.7 V, VI = 0 to VCC 300 300 µA IBHHO# VCC = 2.7 V, VI = 0 to VCC –300 –300 µA IEX|| VCC = 2.3 V, VO = 5.5 V 125 125 µA IOZ(PU/PD)k VCC ≤ 1.2 V, VO = 0.5 V to VCC, VI = GND or VCC, OE = don’t care ±100 ±100 µA IOZH VCC = 2.7 V VO = 2.3 V, VI = 0.7 V or 1.7 V 5 5 µA IOZL VCC = 2.7 V VO = 0.5 V, VI = 0.7 V or 1.7 V –5 –5 µA VCC = 2.7 V, Outputs high 0.04 0.1 0.04 0.1 ICC VCC = 2.7 V, IO = 0, Outputs low 2.3 5 2.3 5 mA VI = VCC or GND Outputs disabled 0.04 0.1 0.04 0.1 Ci VCC = 2.5 V, VI = 2.5 V or 0 3 3 pF Co VCC = 2.5 V, VO = 2.5 V or 0 6 6 pF † All typical values are at VCC = 2.5 V, TA = 25°C. ‡ The bus-hold circuit can sink at least the minimum low sustaining current at VIL max. IBHL should be measured after lowering VIN to GND and then raising it to VIL max. § The bus-hold circuit can source at least the minimum high sustaining current at VIH min. IBHH should be measured after raising VIN to VCC and then lowering it to VIH min. ¶ An external driver must source at least IBHLO to switch this node from low to high. # An external driver must sink at least IBHHO to switch this node from high to low. || Current into an output in the high state when VO > VCC kHigh-impedance state during power up or power down PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. |
Số phần tương tự - 74ALVTH16827VRG4 |
|
Mô tả tương tự - 74ALVTH16827VRG4 |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |