công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LM124F bảng dữ liệu(PDF) 4 Page - NXP Semiconductors |
|
LM124F bảng dữ liệu(HTML) 4 Page - NXP Semiconductors |
4 / 7 page Philips Semiconductors Product specification LM124/224/324/324A/ SA534/LM2902 Low power quad op amps 1995 Nov 27 4 DC ELECTRICAL CHARACTERISTICS (Continued) VCC=5V, TA=25°C unless otherwise specified. SYMBOL PARAMETER TEST CONDITIONS LM324A UNIT SYMBOL PARAMETER TEST CONDITIONS Min Typ Max UNIT VOS Offset voltage1 RS=0Ω ±2 ±3 mV VOS Offset voltage1 RS=0Ω, over temp. ±5 mV ∆VOS/∆T Temperature drift RS=0Ω, over temp. 7 30 µV/°C IBIAS Input current2 IIN(+) or IIN(-) 45 100 nA IBIAS Input current2 IIN(+) or IIN(-), over temp. 40 200 nA ∆IBIAS/∆T Temperature drift Over temp. 50 pA/ °C IOS Offset current IIN(+)-IIN(-) ±5 ±30 nA IOS Offset current IIN(+)-IIN(-), over temp. ±75 nA ∆IOS/∆T Temperature drift Over temp. 10 300 pA/ °C VCM Common-mode voltage range3 VCC≤30V 0 VCC-1.5 V VCC≤30V, over temp. 0 VCC-2 V CMRR Common-mode rejection ratio VCC=30V 65 85 dB VOUT Output voltage swing RL=2kΩ, VCC=30V, over temp. 26 V VOH Output voltage high RL≤10kΩ, VCC=30V, over temp. 27 28 V VOL Output voltage low RL≤10kΩ, over temp. 5 20 mV ICC Supply current RL=∞, VCC=30V, over temp. 1.5 3 mA RL=∞, over temp. 0.7 1.2 mA AVOL Large-signal voltage gain VCC=15V (for large VO swing), RL≥2kΩ 25 100 V/mV VCC=15V (for large VO swing), RL≥2kΩ, over temp. 15 V/mV Amplifier-to-amplifier coupling5 f=1kHz to 20kHz, input referred -120 dB PSRR Power supply rejection ratio RS≤0Ω 65 100 dB Output current source VIN+=+1V, VIN-=0V, VCC=15V 20 40 mA VIN+=+1V, VIN-=0V, VCC=15V, over temp. 10 20 mA IOUT Output current VIN-=+1V, VIN+=0V, VCC=15V 10 20 mA sink VIN-=+1V, VIN+=0V, VCC=15V, over temp. 5 8 mA VIN-=+1V, VIN+=0V, VO=200mV 12 50 µA ISC Short-circuit current4 10 40 60 mA VDIFF Differential input voltage3 VCC V GBW Unity gain bandwidth 1 MHz SR Slew rate 0.3 V/ µs VNOISE Input noise voltage f=1kHz 40 nV/ √Hz NOTES: 1. VO ≈ 1.4VDC, RS=0Ω with VCC from 5V to 30V and over full input common-mode range (0VDC+ to VCC -1.5V). 2. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so no loading change exists on the input lines. 3. The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is VCC -1.5, but either or both inputs can go to +32V without damage. 4. Short-circuits from the output to VCC can cause excessive heating and eventual destruction. The maximum output current is approximately 40mA independent of the magnitude of VCC. At values of supply voltage in excess of +15VDC, continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result from simultaneous shorts on all amplifiers. 5. Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This typically can be detected as this type of coupling increases at higher frequencies. |
Số phần tương tự - LM124F |
|
Mô tả tương tự - LM124F |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |