STM706TM6F datasheet(9/26 Pages) STMICROELECTRONICS

tên linh kiện	STM706TM6F

Giải thích chi tiết về linh kiện	3V Supervisor

Download	26 Pages

Scroll/Zoom	100%

nhà sản xuất	STMICROELECTRONICS [STMicroelectronics]

Trang chủ	http://www.st.com

Logo

9 / 26 page

9/26

STM706T/S/R; STM706P; STM708T/S/R

OPERATION

Reset Output

The STM70x Supervisor asserts a reset signal to

the MCU whenever VCC goes below the reset

threshold (VRST), a watchdog time-out occurs (if

WDO is connected to MR), or when the Push-but-

ton Reset Input (MR) is taken low. RST is guaran-

teed to be a logic low (logic high for STM706P and

STM708T/S/R) for VCC < VRST down to VCC =1V

for TA = 0°C to 85°C.

During power-up, once VCC exceeds the reset

threshold an internal timer keeps RST low for the

reset time-out period, trec. After this interval RST

returns high.

If VCC drops below the reset threshold, RST goes

low. Each time RST is asserted, it stays low for at

least the reset time-out period (trec). Any time VCC

goes below the reset threshold the internal timer

clears. The reset timer starts when VCC returns

above the reset threshold.

Push-button Reset Input

A logic low on MR asserts reset. Reset remains

asserted while MR is low, and for trec (see Figure

29., page 19) after it returns high. The MR input

has an internal 40k

Ω pull-up resistor, allowing it to

be left open if not used. This input can be driven

with TTL/CMOS-logic levels or with open-drain/

collector outputs. Connect a normally open mo-

mentary switch from MR to GND to create a man-

ual reset function; external debounce circuitry is

not required. If MR is driven from long cables or

the device is used in a noisy environment, connect

a 0.1µF capacitor from MR to GND to provide ad-

ditional noise immunity. MR may float, or be tied to

VCC when not used.

Watchdog Input (STM706T/S/R and STM706P)

The watchdog timer can be used to detect an out-

of-control MCU. If the MCU does not toggle the

Watchdog Input (WDI) within tWD (1.6sec), the

Watchdog Output pin (WDO) is asserted. The in-

ternal 1.6sec timer is cleared by either:

1.

a reset pulse, or

2.

by toggling WDI (high-to-low or low-to-high),

which can detect pulses as short as 50ns.

See Figure 30., page 19 for STM706T/S/R and

STM706P.

The timer remains cleared and does not count for

as long as reset is asserted. As soon as reset is re-

leased, the timer starts counting.

Watchdog Output (STM706T/S/R and

STM706P)

When VCC drops below the reset threshold, WDO

will go low even if the watchdog timer has not yet

timed out. However, unlike the reset output, WDO

goes high as soon as VCC exceeds the reset

threshold. WDO may be used to generate a reset

pulse by connecting it to the MR input.

Power-fail Input/Output

The Power-fail Input (PFI) is compared to an inter-

nal reference voltage (independent from the VRST

comparator). If PFI is less than the power-fail

threshold (VPFI), the Power-Fail Output (PFO) will

go low. This function is intended for use as an un-

dervoltage detector to signal a failing power sup-

ply. Typically PFI is connected through an external

voltage divider (see Figure 10., page 8) to either

the unregulated DC input (if it is available) or the

regulated output of the VCC regulator. The voltage

divider can be set up such that the voltage at PFI

falls below VPFI several milliseconds before the

regulated VCC input to the STM70x or the micro-

processor drops below the minimum operating

voltage.

If the comparator is unused, PFI should be con-

nected to VSS and PFO left unconnected. PFO

may be connected to MR on the STM70x so that a

low voltage on PFI will generate a reset output.

Ensuring a Valid Reset Output Down to

VCC =0V

When VCC falls below 1V, the state of the RST out-

put can no longer be guaranteed, and becomes

essentially an open circuit. If a high value pull-

down resistor is added to the RST pin, the output

will be held low during this condition. A resistor val-

ue of approximately 100k

Ω will be large enough to

not load the output under operating conditions, but

still sufficient to pull RST to ground during this low

voltage condition (see Figure 11).

Figure 11. Reset Output Valid to Ground

Circuit

AI08844

STM70x

RST

R1

Số phần tương tự - STM706TM6F

nhà sản xuất	tên linh kiện	bảng dữ liệu	Giải thích chi tiết về linh kiện
STMicroelectronics	STM706TM6F	701Kb / 33P	3 V supervisor

More results

Mô tả tương tự - STM706TM6F

nhà sản xuất	tên linh kiện	bảng dữ liệu	Giải thích chi tiết về linh kiện
STMicroelectronics	STM690	657Kb / 32P	3V Supervisor with Battery Switchover
	STM690	445Kb / 31P	3V Supervisor with Battery Switchover
	M40SZ100Y	285Kb / 19P	5V or 3V NVRAM SUPERVISOR FOR LPSRAM
	M40SZ100Y	230Kb / 25P	5V or 3V NVRAM supervisor for LPSRAM
	STM1403	162Kb / 9P	3V FIPS-140 Security Supervisor with Battery Switchover
	M40Z300AV	272Kb / 20P	3V NVRAM Supervisor for Up to 8 LPSRAMs
	M40Z111	180Kb / 21P	5V or 3V NVRAM supervisor for up to two LPSRAMs
	M40Z111	107Kb / 15P	5V OR 3V NVRAM SUPERVISOR FOR UP TO TWO LPSRAMs
	M40Z300	221Kb / 25P	5V or 3V NVRAM supervisor for up to 8 LPSRAMs
	M40Z300	348Kb / 21P	5V or 3V NVRAM Supervisor for Up to 8 LPSRAMs

More results

STM706TM6F bảng dữ liệu(PDF) 9 Page - STMicroelectronics

STM706TM6F bảng dữ liệu(HTML) 9 Page - STMicroelectronics

Số phần tương tự - STM706TM6F

Mô tả tương tự - STM706TM6F

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

bảng dữ liệu tải về

Link URL