công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LM3207 bảng dữ liệu(PDF) 6 Page - National Semiconductor (TI) |
|
|
LM3207 bảng dữ liệu(HTML) 6 Page - National Semiconductor (TI) |
6 / 19 page Note 5: Junction-to-ambient thermal resistance ( θJA) is taken from thermal measurements, performed under the conditions and guidelines set forth in the JEDEC standard JESD51-7. Note 6: Min and Max limits are guaranteed by design, test, or statistical analysis. Typical numbers are not guaranteed, but do represent the most likely norm. Due to the pulsed nature of the testing TA =TJ for the electrical characteristics table. Note 7: The parameters in the electrical characteristics table are tested under open loop conditions at PVIN = 3.6V. For performance over the input voltage range and closed loop results refer to the datasheet curves. Note 8: Shutdown current includes leakage current of PFET. Note 9: IQ specified here is when the part is operating at 100% duty cycle. Note 10: Current limit is built-in, fixed, and not adjustable. Refer to datasheet curves for closed loop data and its variation with regards to supply voltage and temperature. Electrical Characteristic table reflects open loop data (FB = 0V and current drawn from SW pin ramped up until cycle by cycle limit is activated). Closed loop current limit is the peak inductor current measured in the application circuit by increasing output current until output voltage drops by 10%. Note 11: Ripple voltage should measured at COUT electrode on good layout PC board and under condition using suggested inductors and capacitors. Note 12: Transient Pull-up current (IPUT) and Transient Pull-down Current (IPDT) will be tested which are inversely proportional to charge and discharge times tLDO, ON and tLDO, OFF respectively. Note 13: Dropout voltage is the voltage difference between the input and the output at which the output voltage drops to 100 mV below its nominal value. Typical Performance Characteristics (Circuit in Figure 3, See Operation Description Section), PV IN = EN = 3.6V, L = 3.0µH, (DCR = 0.12 Ω, FDK MIPW3226D3R0M); C IN = 10µF, (6.3V, 0805, TDK C2012X5R0J106K); C OUT = 4.7µF, (6.3V, 0603, TDK C1608X5R0J475M), CLDO = 100nF, 10V, (0402, TDK C1005X5R1A104KT) (or 220nF, (6.3V, 0402, TDK C1005X5R0J224KT)) can be used. T A = 25˚C unless otherwise specified. LDO Typical Performance Curves LDO Voltage vs Load Current (C LDO = 100nF) LDO Dropout Voltage vs Load Current (C LDO = 100nF), (Note 13) 20165378 20165330 LDO Short Circuit Current vs Voltage (V IN = 3.0V, CLDO = 100nF) LDO Output Noise Density (I LOAD = 1mA, CLDO = 100nF and 220nF) 20165360 20165380 www.national.com 6 |
Số phần tương tự - LM3207 |
|
Mô tả tương tự - LM3207 |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |