công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
ADS5242IPAPT bảng dữ liệu(PDF) 2 Page - Texas Instruments |
|
|
ADS5242IPAPT bảng dữ liệu(HTML) 2 Page - Texas Instruments |
2 / 29 page www.ti.com ABSOLUTE MAXIMUM RATINGS (1) ADS5242 SBAS330C – OCTOBER 2004 – REVISED OCTOBER 2005 This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION(1) SPECIFIED PACKAGE TEMPERATURE PACKAGE ORDERING TRANSPORT PRODUCT PACKAGE-LEAD(2) DESIGNATOR RANGE MARKING NUMBER MEDIA, QUANTITY ADS5242IPAP Tray, 160 ADS5242 HTQFP-64 PAP –40 °C to +85°C ADS5242IPAP ADS5242IPAPT Tape and Reel, 250 (1) For the most current package and ordering information, see the Package Option Addendum located at the end of this data sheet. (2) Thermal pad size: 5.29mm × 5.29mm (min), 6.50mm × 6.50mm (max). Supply Voltage Range, AVDD –0.3V to +3.8V Supply Voltage Range, LVDD –0.3V to +3.8V Voltage Between AVSS and LVSS –0.3V to +0.3V Voltage Between AVDD and LVDD –0.3V to +0.3V Voltage Applied to External REF Pins –0.3V to +2.4V All LVDS Data and Clock Outputs –0.3V to +2.4V Analog Input Pins(2) –0.3V to min. [3.3V, (AVDD + 0.3V)] Operating Free-Air Temperature Range, TA –40 °C to +85°C Lead Temperature, 1.6mm (1/16" from case for 10s) +260 °C Junction Temperature +105 °C Storage Temperature Range –65 °C to +150°C (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not supported. (2) The DC voltage applied on the input pins should not go below –0.3V. Also, the DC voltage should be limited to the lower of either 3.3V or (AVDD + 0.3V). If the input can go higher than +3.3V, then a resistor greater than or equal to 25 Ω should be added in series with each of the input pins. Also, the duty cycle of the overshoot beyond +3.3V should be limited. The overshoot duty cycle can be defined either as a percentage of the time of overshoot over a clock period, or over the entire device lifetime. For a peak voltage between +3.3V and +3.5V, a duty cycle up to 10% is acceptable. For a peak voltage between +3.5V and +3.7V, the overshoot duty cycle should not exceed 1%. Any overshoot beyond +3.7V should be restricted to less than 0.1% duty cycle, and never exceed +3.9V. 2 |
Số phần tương tự - ADS5242IPAPT |
|
Mô tả tương tự - ADS5242IPAPT |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |