công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
1T14A-3RP bảng dữ liệu(PDF) 1 Page - GAPTEC Electronic GmbH & Co. KG |
|
1T14A-3RP bảng dữ liệu(HTML) 1 Page - GAPTEC Electronic GmbH & Co. KG |
1 / 3 page GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 1 of 3 1D14A_3RP & 1T14A_3RP – Rev. 2017-1.7 Specifications subject to change without notice. 1D14A_3RP & 1T14A_3RP Series 1W - Single Output DC-DC Converter - Fixed Input - Isolated - Regulated Small footprint, ultra compact package 3KVDC Isolation Temperature range: -40°C to +85°C No External component Required Industry standard pinout Compatible with DCP01 series Short circuit protection (SCP) RoHS compliance Regulated output with short circuit protection DC-DC Converter 1 Watt The 1D14A_3RP & 1T14A_3RP Series are specially designed for applications where a group of polar power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) Where the voltage of the input power supply is fixed (voltage variation ≤ ±5%) 2) Where isolation is necessary between input and output (isolation voltage ≤3000VDC) 3) Where the regulation of the output voltage and the output ripple noise are not demanding Such as: purely digital circuits, ordinary low frequency analog circuits, and IGBT power device driving circuits. Common specifications Short circuit protection: Continuous, self-recovery Temperature rise at full load: 25°C MAX, 15°C TYP Cooling: Free air convection Operation temperature range: -40°C~+85°C Storage temperature range: -55°C ~+125°C Pin welding resistance temperature: 250°C MAX, 1.5mm from case for 10 sec Reflow soldering temperature: Peak temp. ≤245°C, maximum dura- tion time ≤60s at 217°C. For actual application, please refer to IPC/JEDEC J-STD-020D.1. Storage humidity range: < 95% Casing material: Epoxy Resin [UL94-V0] MTBF: >3,500,000 hours Weight: 1.4g Isolation specifications Item Test condition Min Typ Max Units Isolation voltage Tested for 1 minute and 1mA max 3000 VDC Isolation resistance Test at 500VDC 1000 MΩ Isolation Capacitance 25 pF Note: 1. If the product is operated under the min. required load, the product perfor- mance cannot be guaranteed to comply with all performance indexes in this datasheet; 2. The max. capacitive load should be tested within the input voltage range and under full load conditions; 3. Unless otherwise specified, data in this data sheet should be tested under the conditions of Ta=25°C, humidity<75% when inputting nominal voltage and outputting rated load; 4. All index testing methods in this datasheet are based on our Company’s corpo- rate standards; 5. The performance indexes of the product models listed in this manual are as above, but some indexes of non-standard model products will exceed the above- mentioned requirements, and please directly contact our technicians for specific information; 6. We can provide product customization service; 7. Specifications of this product are subject to changes without prior notice. Model selection: WCTP**_xxyyN##O W=Watt; C= Case; T=Type; P=Pinning; **= Voltage Variation (omitted ± 10%); xx= Vin; yy= Vout; N= Numbers of Output; ##= Isolation (kVDC); O= output regulation Example: 1D14A_0505S3RP 1=1Watt; D14=DIP14; A=Pinning; 5Vin; 5Vout; S=Single Output 3=3kVDC; R=Regulated Output; P=Short Ciruit Protection Output specifications Item Test condition Min Typ Max Units Output voltage accuracy ±3 % Line regulation For Vin change of 5% ±0.25 % Load regulation 10% to 100% load ±1 % Temperature drift 100% full load ±0.03 %/°C Ripple & Noise* 20MHz Bandwidth • Ripple • Noise 10 50 20 75 mVp-p mVp-p Switching frequency Full load, nominal input 100 KHz * Test ripple and noise by “parallel cable” method. See detailed operation instruc- tions at Testing of Power Converter section, application notes. Input specifications Item Test condition Min Typ Max Units Input current (full load / no load) • 5V input •12V input 285/25 115/20 mA Surge voltage • 5V input •12V input -0.7 -0.7 9 18 VDC VDC Input filter Capacitor filter |
Số phần tương tự - 1T14A-3RP |
|
Mô tả tương tự - 1T14A-3RP |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |