công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
GS-R24P0001.5 bảng dữ liệu(PDF) 5 Page - STMicroelectronics |
|
GS-R24P0001.5 bảng dữ liệu(HTML) 5 Page - STMicroelectronics |
5 / 7 page 5/7 GS-R24P USER NOTES Input Voltage The recommended operating maximum DC Input Voltage is 35V inclusive of ripple voltage. Inhibit function The inhibit feature allows to put in stand-by mode the device. With INH pin 4 higher than 2.2V the device is disabled and the power consumption is reduced to less than 150µA for Vi = 35V. With INH pin lower than 0.8V, the device is enabled. If the INH pin is left floating, an internal pull up ensures that the voltage at the pin reaches the inhibit threshold and the device is disabled. The pin is also Vi compatible. Current protection The device has two current limit protections, pulse by pulse and frequency fold back. The current is sensed through a resistor and if reaches the threshold, the on time is reduced and consequently the output voltage too. Since the minimum switch ON time (necessary to avoid false overcurrent signal) is not enough to obtain a suf- ficiently low duty cycle at 250 Hz, the output current, in strong overcurrent or short circuit conditions, could in- crease again. For this reason the switching frequency is also reduced, so keeping the inductor current under its maximum threshold. The frequency depends on the feedback voltage. As the feedback voltage decreases (due to the reduced duty cycle), the switching frequency decrease too. Thermal shutdown The shutdown block generates a signal that turns off the power stage if the temperature of the internal chip goes higher than a fixed internal threshold (150 ºC). The sensing element of the chip is very close to the PDMOS area, so ensuring an accurate and fast temperature detection. An hysteresis of approximately 20ºC avoids that the devices turns on and off continuously. Thermal Characteristics Output voltage programming (GS-R24H(S)0001.5 only) The GS-R24P output voltage is 5.54V ±4%, to reduce this value connect a resistor between pin 6 (FB) and pin 5 (Vout-c). The resistor must be located very close to the proper pins, to minimize the injected noise (see figure 1). The resistor value is calculated using the following formula: Rv=[(Vout-1.235)*11.3]/(5.54-Vout) --[kOhm] Vout can be adjusted between 1.235V (Rv=0 Ohm) and 5.54V (Rv=open) |
Số phần tương tự - GS-R24P0001.5 |
|
Mô tả tương tự - GS-R24P0001.5 |
|
|
Link URL |
Chính sách bảo mật |
ALLDATASHEET.VN |
Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |