 |
công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
|
công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
AD7703AR bảng dữ liệu(PDF) 5 Page - Analog Devices |
|
||||||||||||||||||||||||||||||
AD7703AR bảng dữ liệu(HTML) 5 Page - Analog Devices |
|
|
5 / 17 page  REV. E –4– AD7703 Limit at TMIN, TMAX Limit at TMIN, TMAX Parameter (A, B Versions) (S, T Versions) Unit Conditions/Comments fCLKIN 3, 4 200 200 kHz min Master Clock Frequency: Internal Gate Oscillator 55 MHz max Typically 4.096 MHz 200 200 kHz min Master Clock Frequency: Externally Supplied 55 MHz max tr 5 50 50 ns max Digital Output Rise Time. Typically 20 ns. tf 5 50 50 ns max Digital Output Fall Time. Typically 20 ns. t1 00 ns min SC1, SC2 to CAL High Setup Time t2 50 50 ns min SC1, SC2 Hold Time after CAL Goes High t3 6 1000 1000 ns min SLEEP High to CLKIN High Setup Time SSC MODE t4 7 3/fCLKIN 3/fCLKIN ns max Data Access Time (CS Low to Data Valid) t5 100 100 ns max SCLK Falling Edge to Data Valid Delay (25 ns typ) t6 250 250 ns min MSB Data Setup Time. Typically 380 ns. 7 300 300 ns max SCLK High Pulsewidth. Typically 240 ns. t8 790 790 ns max SCLK Low Pulsewidth. Typically 730 ns. t9 8 l/fCLKIN + 200 l/fCLKIN + 200 ns max SCLK Rising Edge to Hi-Z Delay (l/fCLKIN + 100 ns typ) t10 8, 9 4/fCLKIN + 200 4/fCLKIN + 200 ns max CS High to Hi-Z Delay SEC MODE fSCLK 55 MHz max Serial Clock Input Frequency t11 35 35 ns min SCLK Input High Pulsewidth t12 160 160 ns min SCLK Low Pulsewidth t13 7, 10 160 160 ns max Data Access Time (CS Low to Data Valid). Typically 80 ns. t14 11 150 150 ns max SCLK Falling Edge to Data Valid Delay. Typically 75 ns. t15 8 250 250 ns max CS High to Hi-Z Delay t16 8 200 200 ns max SCLK Falling Edge to Hi-Z Delay. Typically 100 ns. NOTES 1Sample tested at 25°C to ensure compliance. All input signals are specified with t r = tf = 5 ns (10% to 90% of 5 V) and timed from a voltage level of 1.6 V. 2See Figures 1 to 6. 3CLKIN duty cycle range is 20% to 80%. CLKIN must be supplied whenever the AD7703 is not in SLEEP mode. If no clock is present in this case, the device can draw higher current than specified and possibly become uncalibrated. 4The AD7703 is production tested with f CLKIN at 4.096 MHz. It is guaranteed by characterization to operate at 200 kHz. 5Specified using 10% and 90% points on waveform of interest. 6In order to synchronize several AD7703s together using the SLEEP pin, this specification must be met. 7t 4 and t13 are measured with the load circuit of Figure 1 and defined as the time required for an output to cross 0.8 V or 2.4 V. 8t 9, t10, t15, and t16 are derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 1. The measured number is then extrapolated back to remove the effects of charging or discharging the 100 pF capacitor. This means that the time quoted in the Timing Characteristics is the true bus relinquish time of the part and as such is independent of external bus loading capacitance. 9If CS is returned high before all 20 bits are output, the SDATA and SCLK outputs will complete the current data bit and then go to high impedance. 10If CS is activated asynchronously to DRDY, CS will not be recognized if it occurs when DRDY is high for four clock cycles. The propagation delay time may be as great as four CLKIN cycles plus 160 ns. To guarantee proper clocking of SDATA when using asynchronous CS, the SCLK input should not be taken high sooner than four CLKIN cycles plus 160 ns after CS goes low. 11SDATA is clocked out on the falling edge of the SCLK input. Specifications subject to change without notice. TIMING CHARACTERISTICS1, 2 (AVDD = DVDD = +5 V 10%; AVSS = DVSS = –5 V 10%; AGND = DGND = O V; fCLKIN = 4.096 MHz; Input Levels: Logic O = O V, Logic 1 = DVDD; unless otherwise noted.) CL 100pF TO OUTPUT PIN IOH 200 A 2.1V + IOL 1.6mA Figure 1. Load Circuit for Access Time and Bus Relinquish Time CAL SC1, SC2 SC1, SC2 VALID t 1 t 2 Figure 2. Calibration Control Timing CLKIN SLEEP t 3 Figure 3. Sleep Mode Timing |
Số phần tương tự - AD7703AR |
|
Mô tả tương tự - AD7703AR |
|
|
|
Link URL |
| Chính sách bảo mật |
| ALLDATASHEET.VN |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Vietnamese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
